manualshive.com logo in svg

RAM 1500 2023, Owner'S Manual, Page: 331 / 416

Share
Download
RAM 1500 2023 Owner'S Manual Download Page 331

IN CASE OF EMERGENCY

329

To Reset The Manual Park Release:
1. Apply firm pressure to the brake pedal while seated 

in the driver’s seat.

2. Pull the tether strap out again, then release it.
3. Allow the tether to retract with the lever back to its 

original position.

Manual Park Release Tether

4. Verify the transmission is in PARK.
5. Confirm that the tether has retracted fully and 

reinstall the access cover. If the access cover cannot 

be reinstalled, repeat steps 1 through 4.

NOTE:

When the lever is locked in the released position the 

access cover cannot be reinstalled.

FREEING A STUCK VEHICLE 

If your vehicle becomes stuck in mud, sand, or snow, it can 

often be moved using a rocking motion. Turn the steering 

wheel right and left to clear the area around the front 

wheels. Then shift back and forth between DRIVE (D) and 

REVERSE (R), while gently pressing the accelerator. Use 

the least amount of accelerator pedal pressure that will 

maintain the rocking motion, without spinning the wheels 

or racing the engine.

NOTE:

Shifts between DRIVE and REVERSE can only be achieved 

at wheel speeds of 5 mph (8 km/h) or less. Whenever the 

transmission remains in NEUTRAL (N) for more than two 

seconds, you must press the brake pedal to engage DRIVE 

or REVERSE.
Push the ESC OFF button to place the Electronic Stability 

Control (ESC) system in “Partial OFF” mode, before rocking 

the vehicle  

Ú

page 264. Once the vehicle has been freed, 

push the ESC OFF button to restore “ESC On” mode.

CAUTION!

Racing the engine or spinning the wheels may lead to 

transmission overheating and failure. Allow the 

engine to idle with the transmission in NEUTRAL for 

at least one minute after every five rocking-motion 

cycles. This will minimize overheating and reduce the 

risk of transmission failure during prolonged efforts 

to free a stuck vehicle.

When “rocking” a stuck vehicle by shifting between 

DRIVE and REVERSE, do not spin the wheels faster 

than 15 mph (24 km/h), or drivetrain damage may 

result.

Revving the engine or spinning the wheels too fast 

may lead to transmission overheating and failure.

It can also damage the tires. Do not spin the wheels 

above 30 mph (48 km/h) while in gear (no transmis

-

sion shifting occurring).

WARNING!

Fast spinning tires can be dangerous. Forces generated 

by excessive wheel speeds may cause damage, or even 

failure, of the axle and tires. A tire could explode and 

injure someone. Do not spin your vehicle's wheels 

faster than 30 mph (48 km/h) or for longer than 

30 seconds continuously without stopping when you 

are stuck and do not let anyone near a spinning wheel, 

no matter what the speed.

7

23_DT_OM_EN_USC_t.book  Page 329  

Summary of Contents for 1500 2023

































































































































































































































































































































































































































Reviews:

No comments