manualshive.com logo in svg

RAM 1500 2023, Owner'S Manual, Page: 328 / 416

Share
Download
RAM 1500 2023 Owner'S Manual Download Page 328

326

IN CASE OF EMERGENCY

 

Connecting The Jumper Cables
1. Connect the positive (+) end of the jumper cable to 

the positive (+) post of the discharged vehicle.

NOTE:

Do not jump off fuses. Only jump directly off positive post.
2. Connect the opposite end of the positive (+) jumper 

cable to the positive (+) post of the booster battery.

3. Connect the negative (-) end of the jumper cable to 

the negative (-) post of the booster battery.

4. Connect the opposite end of the negative (-) jumper 

cable to a good engine ground. A “ground” is an 

exposed metallic/unpainted part of the engine, frame 

or chassis, such as an accessory bracket or large bolt. 

The ground must be away from the battery and the 

fuel injection system.

Jump Starting Label

5. Start the engine in the vehicle that has the booster 

battery, let the engine idle a few minutes, and then 

start the engine in the vehicle with the discharged 

battery.

6. Once the engine is started, follow the disconnection 

procedure.

Disconnecting The Jumper Cables
1. Disconnect the negative (-) end of the jumper cable 

from the engine ground of the vehicle with the 

discharged battery.

2. Disconnect the opposite end of the negative (-) 

jumper cable from the negative (-) post of the booster 

battery.

3. Disconnect the positive (+) end of the jumper cable 

from the positive (+) post of the booster battery.

4. Disconnect the opposite end of the positive (+) 

jumper cable from the positive (+) post of the vehicle 

with the discharged battery, and reinstall the 

protective cap.

If frequent jump starting is required to start your vehicle 

you should have the battery and charging system 

inspected at an authorized dealer.

REFUELING IN EMERGENCY

The vehicle is equipped with a refueling funnel for a 

Cap-Less Fuel System. The refueling funnel is located 

under the passenger’s seat along with the jack and tools. 

If refueling is necessary, while using an approved gas can, 

insert the refueling funnel into the filler neck opening. 

Take care to open both flappers with the funnel to avoid 

spills.

WARNING!

Do not connect the jumper cable to the negative (-) post 

of the discharged battery. The resulting electrical spark 

could cause the battery to explode and could result in 

personal injury.

CAUTION!

Do not connect jumper cable to any of the fuses on the 

positive battery terminal. The resulting electrical 

current will blow the fuse.

CAUTION!

Accessories plugged into the vehicle power outlets draw 

power from the vehicle’s battery, even when not in use 

(i.e., cellular devices, etc.). Eventually, if plugged in long 

enough without engine operation, the vehicle’s battery 

will discharge sufficiently to degrade battery life and/or 

prevent the engine from starting.

23_DT_OM_EN_USC_t.book  Page 326  

Summary of Contents for 1500 2023

































































































































































































































































































































































































































Reviews:

No comments