RAM 1500 2023 Page 327 Owner'S Manual Download

Page: 327 / 416

IN CASE OF EMERGENCY

325

JUMP STARTING

If your vehicle has a discharged battery, it can be jump

started using a set of jumper cables and a battery in

another vehicle, or by using a portable battery booster

pack. Jump starting can be dangerous if done improperly,

so please follow the procedures in this section carefully.

NOTE:

When using a portable battery booster pack, follow the

manufacturer's operating instructions and precautions.

REPARATIONS

UMP

TART

The battery in your vehicle is located in the front of the

engine compartment, behind the left headlight assembly.

Positive (+) Battery Post Location

NOTE:

The positive battery post may be covered with a protective

cap. Lift up on the cap to gain access to the positive

battery post. Do not jump off fuses. Only jump directly off

positive post which has a positive (+) symbol on or around

the post.
See the following steps to prepare for jump starting:
1. Shift the automatic transmission into PARK, apply

the parking brake and turn the ignition OFF.

2. Turn off the heater, radio, and all electrical

accessories.

3. If using another vehicle to jump start the battery, park

the vehicle within the jumper cables’ reach, apply the

parking brake and make sure the ignition is OFF.

4. Pull upward and remove the protective cover over the

positive (+) battery post.

UMP

TARTING

ROCEDURE

WARNING!

Do not attempt jump starting if the battery is frozen. It

could rupture or explode and cause personal injury.

CAUTION!

Do not use a portable battery booster pack or any other

booster source with a system voltage greater than

12 Volts or damage to the battery, starter motor,

alternator or electrical system may occur.

WARNING!

Do not allow vehicles to touch each other as this could

establish a ground connection and personal injury

could result.

WARNING!



Take care to avoid the radiator cooling fan whenever

the hood is raised. It can start anytime the ignition

switch is ON. You can be injured by moving fan

blades.



Remove any metal jewelry such as rings, watch

bands and bracelets that could make an inadvertent

electrical contact. You could be seriously injured.



Batteries contain sulfuric acid that can burn your

skin or eyes and generate hydrogen gas which is

flammable and explosive. Keep open flames or

sparks away from the battery.

WARNING!

Failure to follow this jump starting procedure could

result in personal injury or property damage due to

battery explosion.

CAUTION!

Failure to follow these procedures could result in

damage to the charging system of the booster vehicle

or the discharged vehicle.

23_DT_OM_EN_USC_t.book Page 325

Summary of Contents for 1500 2023

































































































































































































































































































































































































































Search results

Summary of Contents for 1500 2023

Reviews:

Related manuals for 1500 2023

Brands by name

Popular brands

RAM 1500 2023, Owner'S Manual

Search results

Summary of Contents for 1500 2023

Reviews:

Related manuals for 1500 2023

Brands by name

Popular brands