manualshive.com logo in svg

RAM 1500 2023, Owner'S Manual, Page: 238 / 416

Share
Download
RAM 1500 2023 Owner'S Manual Download Page 238

236

MULTIMEDIA

 

Voice Text Reply — If Equipped
Uconnect can announce incoming text messages. Push 
the VR button 

 or Phone button 

 and say:

1. “Listen” to have the system read an incoming text 

message. (Must have compatible mobile phone 

paired to Uconnect system.)

2. “Reply” after an incoming text message has been 

read.
Listen to the Uconnect prompts. After the beep, re

-

peat one of the predefined messages and follow the 

system prompts.

NOTE:

Only use the numbering listed in the provided table. 

Otherwise, the system will not transpose the message.
Did You Know: Your mobile phone must have the full 

implementation of the Message Access Profile (MAP) to 

take advantage of this feature. For details about MAP, visit 

UconnectPhone.com.
Apple® iPhone® iOS 5 or later supports reading incoming 

text messages only. For further information on how to 

enable this feature on your Apple® iPhone®, refer to your 

iPhone® “User Manual”.
Did You Know: Voice Text Reply is not compatible with 

iPhone®, but if your vehicle is equipped with Siri® Eyes 

Free, you can use your voice to send a text message.
Siri® Eyes Free — If Equipped
When used with your Apple® iPhone® connected to your 

vehicle via Bluetooth®, Siri lets you use your voice to send 

text messages, select media, place phone calls and much 

more. Siri uses your natural language to understand what 

you mean and responds back to confirm your requests. 

The system is designed to keep your eyes on the road and 

your hands on the wheel by letting Siri help you perform 

useful tasks.
To enable Siri, push and hold, then release the Uconnect 

Voice Recognition (VR) button on the steering wheel. After 

you hear a double beep, you can ask Siri to play podcasts 

and music, get directions, read text messages, and many 

other useful requests.

BLUETOOTH® COMMUNICATION LINK

Mobile phones may lose connection to the Uconnect 

Phone. When this happens, the connection can generally 

be re-established by restarting the mobile phone. Your 

mobile phone is recommended to remain in Bluetooth® 

ON Mode.

POWER-UP

After switching the ignition key from OFF to either the 

ON/RUN or ACC position, or after a language change, you 

must wait at least 15 seconds prior to using the system  

Ú

page 402.

CONNECTED VEHICLE SERVICES — 

IF EQUIPPED 

I

S

 M

Y

 V

EHICLE

 C

ONNECTED

?

If equipped, vehicles with an ASSIST and an SOS button 

are connected vehicles. These buttons will be located on 

either the rearview mirror or overhead console, depending 

on the vehicle. If these buttons are present in your vehicle, 

you have a connected radio and can take advantage of the 

many connected vehicle features.
For further information about the ASSIST and SOS buttons  

Ú

page 314.

PRE-DEFINED VOICE TEXT REPLY RESPONSES

Yes.

Stuck in traffic.

See you later.

No.

Start without 

me.

I’ll be late.

Okay.

Where are you?

I will be 5 <or 

10, 15, 20, 25, 

30, 45, 60> 

minutes late.

Call me.

Are you there 

yet?

I’ll call you later.

I need 

directions.

See you in 5 <or 

10, 15, 20, 25, 

30, 45, 60> 

minutes.

I’m on my way.

Can’t talk right 

now.

I’m lost.

Thanks.

23_DT_OM_EN_USC_t.book  Page 236  

Summary of Contents for 1500 2023

































































































































































































































































































































































































































Reviews:

No comments