RAM 1500 2023 Owner'S Manual Download Page 124

Page: 124 / 416

122

STARTING AND OPERATING

ENGINE BREAK-IN RECOMMENDATIONS

A long break-in period is not required for the engine and

drivetrain (transmission and axle) in your vehicle.
Drive moderately during the first 300 miles (500 km).

After the initial 60 miles (100 km), speeds up to 50 or

55 mph (80 or 90 km/h) are desirable.
While cruising, brief full-throttle acceleration within the

limits of local traffic laws contributes to a good break-in.

Wide-open throttle acceleration in low gear can be

detrimental and should be avoided.
The engine oil installed in the engine at the factory is a

high-quality energy conserving type lubricant. Oil changes

should be consistent with anticipated climate conditions

under which vehicle operations will occur. For the

recommended viscosity and quality grades

page 396.

NOTE:

A new engine may consume some oil during its first few

thousand miles (kilometers) of operation. This should be

considered a normal part of the break-in and not inter

preted as a problem. Please check your oil level with the

engine oil indicator often during the break-in period. Add

oil as required.

PARKING BRAKE

LECTRIC

ARK

RAKE

(EPB)

Your vehicle is equipped with an EPB that offers simple

operation, and some additional features that make the

parking brake more convenient and useful.
The parking brake is primarily intended to prevent the

vehicle from rolling while parked. Before leaving the

vehicle, make sure that the parking brake is applied. Also,

be certain to leave the transmission in PARK.
You can engage the parking brake in two ways:



Manually, by applying the parking brake switch.



Automatically, by enabling the Auto Park Brake feature

in the Customer Programmable Features section of the

Uconnect settings.

The parking brake switch is located on the instrument

panel to the left of the steering wheel (below the

headlamp switch).

Electric Park Brake Switch

To apply the parking brake manually, pull up on the switch

momentarily. You may hear a slight sound from the back

of the vehicle while the parking brake engages. Once the

park brake is fully engaged, the BRAKE telltale light in the

instrument cluster and an indicator on the switch will

illuminate. If your foot is on the brake pedal while you

apply the parking brake, you may notice a small amount of

brake pedal movement. The parking brake can be applied

even when the ignition switch is OFF but the BRAKE

telltale light will not illuminate, however, it can only be

released when the ignition is in the ON/RUN position.

NOTE:

The EPB Warning Light will illuminate if the EPB switch is

held for longer than 20 seconds in either the released or

applied position. The light will extinguish upon releasing

the switch.
If the Auto Park Brake feature is enabled, the parking

brake will automatically engage whenever the

transmission is placed into PARK. If your foot is on the

brake pedal, you may notice a small amount of brake

pedal movement while the parking brake is engaging.
The parking brake will release automatically when the

ignition is ON, the transmission is in DRIVE or REVERSE,

the driver seat belt is buckled, and an attempt is made to

drive away.
To release the parking brake manually, the ignition switch

must be in the ON/RUN position. Put your foot on the

brake pedal, then push the parking brake switch down

momentarily. You may hear a slight whirring sound from

the back of the vehicle while the parking brake

disengages.

CAUTION!

Never use Non-Detergent Oil or Straight Mineral Oil in

the engine or damage may result.

23_DT_OM_EN_USC_t.book Page 122

Summary of Contents for 1500 2023

































































































































































































































































































































































































































Search results

Summary of Contents for 1500 2023

Reviews:

RAM 1500 2023, Owner'S Manual, Page: 124 / 416

Search results

Summary of Contents for 1500 2023

Reviews: