RAM 1500 2023 Page 120 Owner'S Manual Download

Page: 120 / 416

118

(Continued)

STARTING AND OPERATING

STARTING THE ENGINE

Before starting your vehicle, adjust your seat, adjust both

inside and outside mirrors, and fasten your seat belt.
The starter should not be operated for more than

10-second intervals. Waiting at least 10 to 15 seconds

between such intervals will protect the starter from

overheating.

UTOMATIC

RANSMISSION

Start the engine with the transmission in PARK position.

Apply the brake before shifting into any driving range.

NOTE:



This vehicle is equipped with a transmission shift inter

locking system. The brake pedal must be pressed to

shift out of PARK.



If equipped with an 8-speed transmission, starting the

vehicle in NEUTRAL is not possible unless the Manual

Park Release has been activated

page 328.

TART

EATURE

Do not press the accelerator. Cycle the ignition switch

briefly to the START position and release it. The starter

motor will continue to run and will automatically

disengage when the engine is running.

EYLESS

NTER

‘

™ — I

GNITION

This feature allows the driver to operate the ignition

switch with the push of a button, as long as the Remote

Start/Keyless Enter ‘n Go™ key fob is in the passenger

compartment.

ORMAL

TARTING

SING

ENGINE

START/STOP B

UTTON

To Turn On The Engine Using The ENGINE START/STOP

Button
1. The transmission must be in PARK.
2. Press and hold the brake pedal while pushing the

ENGINE START/STOP button once.

3. The system starts the vehicle. If the vehicle fails to

start, the starter will disengage automatically after

10 seconds.

4. If you wish to stop the cranking of the engine prior to

the engine starting, push the button again.

WARNING!



When leaving the vehicle, always make sure the

keyless ignition node is in the OFF position, remove

the key fob from the vehicle and lock the vehicle.



Never leave children alone in a vehicle, or with

access to an unlocked vehicle. Allowing children to

be in a vehicle unattended is dangerous for a

number of reasons. A child or others could be seri

ously or fatally injured. Children should be warned

not to touch the parking brake, brake pedal or the

gear selector.



Do not leave the key fob in or near the vehicle, or in

a location accessible to children, and do not leave

the ignition of a vehicle equipped with Keyless Enter

‘n Go™ in the ACC or ON/RUN position. A child could

operate power windows, other controls, or move the

vehicle.



Do not leave children or animals inside parked vehi

cles in hot weather. Interior heat buildup may cause

serious injury or death.

WARNING!

23_DT_OM_EN_USC_t.book Page 118

Summary of Contents for 1500 2023

































































































































































































































































































































































































































Search results

Summary of Contents for 1500 2023

Reviews:

Related manuals for 1500 2023

Brands by name

Popular brands

RAM 1500 2023, Owner'S Manual

Search results

Summary of Contents for 1500 2023

Reviews:

Related manuals for 1500 2023

Brands by name

Popular brands