RAM 1500 2023 Page 115 Owner'S Manual Download

Page: 115 / 416

GETTING TO KNOW YOUR INSTRUMENT PANEL

113

Your vehicle has also been equipped with a TPMS

malfunction indicator to indicate when the system is not

operating properly. The TPMS malfunction indicator is

combined with the low tire pressure telltale. When the

system detects a malfunction, the telltale will flash for

approximately one minute and then remain continuously

illuminated. This sequence will continue upon subsequent

vehicle start-ups as long as the malfunction exists. When

the malfunction indicator is illuminated, the system may

not be able to detect or signal low tire pressure as

intended. TPMS malfunctions may occur for a variety of

reasons, including the installation of replacement or

alternate tires or wheels on the vehicle that prevent the

TPMS from functioning properly. Always check the TPMS

malfunction telltale after replacing one or more tires or

wheels on your vehicle to ensure that the replacement or

alternate tires and wheels allow the TPMS to continue to

function properly.

ELLOW

NDICATOR

IGHTS

Air Suspension Aerodynamic Height

Indicator Light— If Equipped

This light will illuminate when the air

suspension system is set to the Aerodynamic

setting.

Air Suspension Normal Height Indicator

Light— If Equipped

This light will illuminate when the air

suspension system is set to the Normal setting

page 134.

Air Suspension Off-Road 1 Indicator

Light — If Equipped

This light will illuminate when the air

suspension system is set to the Off-Road 1

setting

page 134.

Air Suspension Off-Road 2 Indicator

Light — If Equipped

This light will illuminate when the air

suspension system is set to the Off-Road 2

setting

page 134.

Air Suspension Payload Protection

Indicator Light — If Equipped

This indicator light will illuminate to indicate

that the maximum payload may have been

exceeded or load leveling cannot be achieved

at its current ride height. Protection mode will

automatically be selected to “protect” the air suspension

system, air suspension adjustment is limited due to

payload.

Air Suspension Ride Height Raising

Indicator Light— If Equipped

This light will blink and alert the driver that the

vehicle is changing to a higher ride height.

Air Suspension Ride Height Lowering

Indicator Light— If Equipped

This light will blink and alert the driver that the

vehicle is changing to a lower ride height.

Cargo Light On Indicator Light —

If Equipped

This indicator light will illuminate when the

cargo light is activated by pushing the cargo

light button on the headlight switch.

CAUTION!

The TPMS has been optimized for the original

equipment tires and wheels. TPMS pressures and

warning have been established for the tire size

equipped on your vehicle. Undesirable system

operation or sensor damage may result when using

replacement equipment that is not of the same size,

type, and/or style. Aftermarket wheels can cause

sensor damage. Using aftermarket tire sealants may

cause the Tire Pressure Monitoring System (TPMS)

sensor to become inoperable. After using an

aftermarket tire sealant it is recommended that you

take your vehicle to an authorized dealer to have your

sensor function checked.

23_DT_OM_EN_USC_t.book Page 113

Summary of Contents for 1500 2023

































































































































































































































































































































































































































Search results

Summary of Contents for 1500 2023

Reviews:

Related manuals for 1500 2023

Brands by name

Popular brands

RAM 1500 2023, Owner'S Manual

Search results

Summary of Contents for 1500 2023

Reviews:

Related manuals for 1500 2023

Brands by name

Popular brands