RAM 1500 2023 Page 103 Owner'S Manual Download

Page: 103 / 416

GETTING TO KNOW YOUR INSTRUMENT PANEL

101

IFE

ESET

Use this QR code to access your digital

experience.
Your vehicle is equipped with an

engine oil change indicator system.

The “Oil Change Required” message

will display in the instrument cluster

display for five seconds after a single

chime has sounded, to indicate the

next scheduled oil change interval. The engine oil change

indicator system is duty cycle based, which means the

engine oil change interval may fluctuate, dependent upon

your personal driving style.
Unless reset, this message will continue to display each

time you place the ignition in the ON/RUN position. To turn

off the message temporarily, push and release the OK or

arrow buttons. To reset the oil change indicator system

(after performing the scheduled maintenance), refer to

the following procedure:
1. Without pressing the brake pedal, push the ENGINE

START/STOP button and place the ignition in the

ON/RUN position (do not start the engine).

2. Push and release the down

arrow button to scroll

downward through the main menu to “Vehicle Info.”

3. Push and release the right

arrow button to access

the ”Oil Life” screen.

4. Push and hold the OK button to reset oil life. If

conditions are met, the gauge and numeric display

will update to show 100%. If conditions are not met a

pop-up message of “To reset oil life engine must be

off with ignition in run” will be displayed (for five

seconds), and the user will remain at the Oil Life

screen.

5. Push and release the up

or down

arrow button

to exit the submenu screen.

NOTE:

If the indicator message illuminates when you start the

vehicle, the oil change indicator system did not reset. If

necessary, repeat this procedure.

ISPLAY

ENU

TEMS

Push and release the up

or down

arrow button until

the desired selectable menu icon is highlighted in the

instrument cluster display.

Speedometer

Push and release the up

or down

arrow button

until the speedometer menu item is highlighted in the

instrument cluster display. Push and release the OK

button to cycle the display between mph and km/h.

Driver Assist — If Equipped

The Driver Assist menu displays the status of the ACC and

LaneSense systems.

Push and release the up

or down

arrow button

until the Driver Assist menu is displayed in the instrument

cluster display.

Adaptive Cruise Control (ACC) Feature
The instrument cluster display displays the current ACC

system settings. The information displayed depends on

ACC system status.
Push the ACC on/off button (located on the steering

wheel) until one of the following displays in the instrument

cluster display:
Adaptive Cruise Control Off
When ACC is deactivated, the display will read “Adaptive

Cruise Control Off.”
Adaptive Cruise Control Ready
When ACC is activated but the vehicle speed setting has

not been selected, the display will read “Adaptive Cruise

Control Ready.”
Push the SET + or the SET- button (located on the steering

wheel) and the following will display in the instrument

cluster display:
ACC SET
When ACC is set, the set speed will display in the

instrument cluster

page 145.

The ACC screen may display once again if any ACC activity

occurs, which may include any of the following:



Distance Setting Change



System Cancel



Driver Override



System Off



ACC Proximity Warning



ACC Unavailable Warning

23_DT_OM_EN_USC_t.book Page 101

Summary of Contents for 1500 2023

































































































































































































































































































































































































































Search results

Summary of Contents for 1500 2023

Reviews:

Related manuals for 1500 2023

Brands by name

Popular brands

RAM 1500 2023, Owner'S Manual

Search results

Summary of Contents for 1500 2023

Reviews:

Related manuals for 1500 2023

Brands by name

Popular brands