Raisecom RC3000-15 Hardware Description Download

Page: 180 / 273

Raisecom
RC3000-15 (P100R001) Hardware Description

10 Data cards

Raisecom Proprietary and Confidential

155

10.6.2 Version

Card

Version

RC3000-15-HT-8FE16E1

10.6.3 Slots

Chassis version

Slot

E.30 and E.20

1–6 and 9–13

10.6.4 Interfaces

Interface type

Table 10-31 lists interfaces on the HT-8FE16E1 card.

Table 10-31

Interfaces on the HT-8FE16E1 card

Name

Type

Description

1–8

RJ45

8 Ethernet electrical interfaces

Interface parameter

Table 10-32 lists parameters of the Ethernet electrical interface.

Table 10-32

Parameters of the Ethernet electrical interface

Parameter

Description

Interface type

RJ45

Interface rate

10/100 Mbit/s auto-negotiation

Duplex mode

Full/Half duplex auto-negotiation

By default, 8 FE electrical interfaces are configured to 100 Mbit/s and full duplex
mode.

Summary of Contents for RC3000-15


















































































































































































































































































Search results

Summary of Contents for RC3000-15

Reviews:

Related manuals for RC3000-15

Brands by name

Popular brands

Raisecom RC3000-15, Hardware Description

Search results

Summary of Contents for RC3000-15

Reviews:

Related manuals for RC3000-15

Brands by name

Popular brands