Raisecom RC3000-15 Page 152 Hardware Description Download

Page: 152 / 273

Raisecom
RC3000-15 (P100R001) Hardware Description

9 Asynchronous data cards

Raisecom Proprietary and Confidential

127

9.3 8RS485

9.3.1 Functions and appearance

Panel

Function

The 8RS485 is an 8-way RS485/422 data service access card. It
provides the following functions:



Provide 8 RJ45 interfaces which can be configured to RS485 or
RS422.



Support configuring a single way to 2-wire half duplex (RS485) or
4-wire full duplex (RS422).



Support configuring the bandwidth allocated for each serial
interface to N×64 kbit/s (N = 1, 2, 4, 8, 16, or 32).



Support a maximum serial rate of 460.8 kbit/s.



Support EMC and overcurrent protection on interfaces.



Support channel external loopback (at TTL level side, digital
loopback).

Summary of Contents for RC3000-15


















































































































































































































































































Search results

Summary of Contents for RC3000-15

Reviews:

Related manuals for RC3000-15

Brands by name

Popular brands

Raisecom RC3000-15, Hardware Description

Search results

Summary of Contents for RC3000-15

Reviews:

Related manuals for RC3000-15

Brands by name

Popular brands