Raisecom RC3000-15 Page 140 Hardware Description Download

Page: 140 / 273

Raisecom
RC3000-15 (P100R001) Hardware Description

9 Asynchronous data cards

Raisecom Proprietary and Confidential

115

9.1 16RS232

9.1.1 Functions and appearance

Panel

Function

The 16RS232 is a 16-way RS232 service access card. It provides the
following functions:



Provide 16 RS232 interfaces. Bandwidth of each interface is
configurable and is up to 1024 kbit/s.



Support multiple serial interface server modes.



Support EMC and overcurrent protection on interfaces.



Support independent outwards loopback (at TTL level side, digital
loopback) for data channels.

Summary of Contents for RC3000-15


















































































































































































































































































Search results

Summary of Contents for RC3000-15

Reviews:

Related manuals for RC3000-15

Brands by name

Popular brands

Raisecom RC3000-15, Hardware Description

Search results

Summary of Contents for RC3000-15

Reviews:

Related manuals for RC3000-15

Brands by name

Popular brands