background image

Raisecom 
RC3000-15 (P100R001) Hardware Description 

8 Voice cards 

 

 

Raisecom Proprietary and Confidential 

Copyright © Raisecom Technology Co., Ltd. 

82 

 

Table 8-16

 

Parameters of the interface on the 16E&M/8E&M/4E&M card 

Parameter 

Description 

Coding scheme 

A-law 

Bit rate 

64 kbit/s 

Audio port impedance 

On-hook impedance is 2 MΩ. 

Off-hook loopback impedance is 600+200//0.1. 

Effective transmission 
bandwidth 

300–3400 Hz/600 Ω 

Gain frequency features 

The Rx (A/D) gain ranges from -3 to 27 dB. The default value 
is controlled by the internal jumper. Its step is 0.1 dB. 

The Tx (D/A) gain ranges from -13 to 7 dB. The default value 
is controlled by the internal jumper. Its step is 0.1 dB. 

Frequency distortion 

300–3000 Hz; < 0.5 dB 

3000–3400 Hz; < 3.0 dB 

Total distortion (1020 
Hz)   

0 to -30 dBm0; < 33 dB 

-30 to -40 dBm0; < (33–22) dB 

-40 to -45 dBm0; < 22 dB 

Gain change according 
to level 

+3 to -40 dBm0; ∆ < 0.5 dB 

-40 to -50 dBm0; ∆ < 1.0 dB 

-50 to -55 dBm0; ∆ < 3.0 dB 

Degree of unbalance 
about earth 

300–600 Hz: > 40 dB 

600–2400 Hz: > 46 dB 

2400–3400 Hz: > 41 dB 

Idle channel noise 

< -67 dBm0p 

Feed voltage (off-hook)    Typical -48 V 

Feed current 

Typical 20 mA 

Ringing voltage 

Typical 60 V/30 Hz 

Return loss 

300–600 Hz: > 12 dB 

600–3400 Hz: > 15 dB 

 

Summary of Contents for RC3000-15


















































































































































































































































































Reviews: