manualshive.com logo in svg

Raisecom RC1104-FE-4 A, User Manual

Share
Download
Raisecom RC1104-FE-4 A User Manual Download Page 13

Raisecom 
RC1104-FE-4W (A) User Manual 

3  Preparing  for  installation  and  connecting  cables 

 

 

Raisecom Technology Co., Ltd. 

6 

 

Table 3-3

 

Device models on both local and remote ends 

Local end 

Remote end 

RC1108-SHDSL-2W×8 

RC1104-FE-4W 

 

3.5 Connecting to other device (electrical interface) 

 

Use the Cat. 5 twisted-pair cable to connect the RC1104-FE-4W to other devices. 
The length of the twisted-pair cable cannot exceed 100m. 

When the RC1104-FE-4W is self-adaptively connected to other devices through the electrical 
interface, the rate of the electrical interface on other device supports 10/100 Mbit/s auto-
negotiation. 

Table 3-4

 

Connection mode 

Modem 

Other device 

RJ45 interface wiring 

RC1104-FE-4W 

Switch 

Straight-through and crossover 

HUB 

Straight-through and crossover 

Router 

Crossover and straight-through 

NIC 

Crossover and straight-through 

 

3.6  Installing device to chassis 

Install the RC1104-FE-4W as below: 

Step 1

 

Install the 19-inch 3U standard RC002-16 chassis or single-slot chassis on the rack. 

Step 2

 

Align the RC1104-FE-4W with the guiderail and insert it into the chassis. 

Step 3

 

Fasten the RC1104-FE-4W with captive screws, as shown in Figure 3-4. 

Summary of Contents for RC1104-FE-4 A





























Reviews:

No comments

Brands by name

Popular brands

Load more brands