Raisecom P100R001 Hardware Description Download Page 121

Page: 121 / 273

Raisecom
RC3000-15 (P100R001) Hardware Description

8 Voice cards

Raisecom Proprietary and Confidential

8.5 12MT

8.5.1 Functions and appearance

Panel

Function

The 12MT is a 12-way magneto telephone access card. It provides the
following functions:



Provide 12 magneto telephone interfaces.



Support configurable gain:

–

The Rx A/D gain ranges from -23 to +2 dB, and is 0 dB by default.

–

The Tx D/A gain ranges from -17 to +8 dB, and is -3.5 dB by
default.



Support configuring signaling mode through software:

–

Support original signaling and reverse signaling. By default, it is
original signaling.

–

Support signaling occupation a-bit and b-bit. By default, it is a-bit.



Support configuring signaling mode (original signaling and reverse
signaling).



Support overcurrent protection for voice interfaces and ringing output.



Support online software upgrade.

Avoid short circuit when the 12MT card is running. If short
circuit occurs and ringing lasts 10 minutes, the 12MT card will
be damaged.

Summary of Contents for P100R001


















































































































































































































































































Search results

Summary of Contents for P100R001

Reviews:

Related manuals for P100R001

Brands by name

Popular brands

Raisecom P100R001, Hardware Description

Search results

Summary of Contents for P100R001

Reviews:

Related manuals for P100R001

Brands by name

Popular brands