Raisecom P100R001 Hardware Description Download Page 105 | Manualshive

Page: 105 / 273

background image

Raisecom
RC3000-15 (P100R001) Hardware Description

8 Voice cards

Raisecom Proprietary and Confidential

Copyright © Raisecom Technology Co., Ltd.

80

8.3 16E&M/8E&M/4E&M

8.3.1 Functions and appearance

Panel

Function

The 16E&M/8E&M/4E&M card is a 16-
way/8-way/4-way E&M audio access
card. It provides the following functions:



Support configuring signaling mode:

–

Support original signaling and
reverse signaling. By default, it is
original signaling.

–

Support signaling occupation a-bit
and b-bit. By default, it is a-bit.



Support configuring 2-wire/4-wire
mode through software.



Support configuring voice gain
through software:

–

The Rx D/A gain ranges from -3 to
27 dB.

–

The Tx D/A gain ranges from -13 to
+7 dB.



Support three default configurations, as
listed in Table 8-14. When the card
leaves factory, the configuration is the
third one. Configuring jumper
implements three default
configurations, but has lower priority
than configuring through network
management. For details, see section
8.3.6 Internal jumper.



Support inwards loopback for analog
audio and outwards loopback for
analog audio (in 4-wire mode only),
and support inwards loopback for
E&M signaling.



Support querying signaling status.



The E&M signaling type is fixed to V.

«
...
103
104
105
106
107
...
»

Summary of Contents for P100R001


















































































































































































































































































Reviews:

No comments

Related manuals for P100R001

Brand: Greenlee Pages: 72

MiniPlex-2USB NMEA-0183

Brand: ShipModul Pages: 22

Brand: Targus Pages: 34

Brand: Perel Pages: 60

Brand: Keysight Pages: 57

Brand: Ikegami Pages: 2

Brand: Mastech Pages: 56

Brand: Hazet Pages: 88

Brand: GB Pages: 3

Brand: GB Pages: 3

Brand: twintex Pages: 2

Brand: koban Pages: 40

Brand: koban Pages: 41

Brand: National Instruments Pages: 128

Brand: BTI Pages: 228

Multiserver 500

Brand: Black Box Pages: 104

Brand: Jeulin Pages: 34

Brand: NTLO Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands