Raisecom iTN8600-I Product Description Download

Page: 18 / 71

Raisecom
iTN8600-I (A) Product Description

1 Overview

Raisecom Proprietary and Confidential

Mode

Client-side

service

Panel interface

Optical module

encapsulation type

Client-side

ODUk cross

connection

OTN

OTU2

1–16

SFP+

Supported

17 (fanned out into
4 interfaces
numbering 19–22)

QSFP+ PSM4

Hybrid

16G FC

9–16

SFP+(it needs to
supports 16G FC, up
to 6 ways)

Not supported
(namely,
Mapper mode)

10G Any

9–16

SFP+

OTU2

1–8

SFP+

Supported
(namely, OTN
mode)

17 (fanned out into
4 interfaces
numbering 19–22)

QSFP+ PSM4



The QSFP+ is a 40GE optical module, using the fiber with the Little Connector
(LC) interface.



The QSFP+ PSM4 is a 4



10GE optical module, using the fiber with the Multiple-

Fiber Push-On (MPO) interface.



QSFP+PSM4 fanout: when the QSFP+ PSM4 optical module uses the MPO-LC
branch optical fiber jumper, one MPO interface fiber can be fanned out into 4 dual-
fiber LC interface fibers to be connected to 4 SFP+ optical modules.

1.3.2 Purchased parts

Parts

The power supplies, fans, rack mount kits (brackets) can be additionally purchased.

Table 1-3

Ordering information about purchased parts

Model

Description

RPD1304-48S12



-48 VDC power supply



Power input: -48 V, 4 A

RPA1171-220S12



220 VAC power supply



Power input: 100–240 V, 1.9 A, 50/60 Hz

FANS383

Fan

Power supply black
panel/RoHS

Power supply black panel, with the ordering model of
RC8.041.1349

Rack mount
kit/RoHS

Bracket used for the 19-inch cabinet, with the ordering model of
RC8.043.169

Summary of Contents for iTN8600-I








































































Search results

Summary of Contents for iTN8600-I

Reviews:

Related manuals for iTN8600-I

Brands by name

Popular brands

Raisecom iTN8600-I, Product Description

Search results

Summary of Contents for iTN8600-I

Reviews:

Related manuals for iTN8600-I

Brands by name

Popular brands