Raisecom iTN2100 Hardware Description Download Page 70 | Manualshive

Page: 70 / 312

Raisecom iTN2100 Hardware Description Download Page 70

Raisecom
iTN2100 (P100R002) Hardware Description

7 SDH tributary cards

Raisecom Technology Co., Ltd.

41

7.2 OPCOM3500E-4STM1-S

7.2.1 Appearance and functions

Appearance

Function

The OPCOM3500E-4STM1-S is a STM-1 tributary card on the iTN2100.



Provide four STM-1 interfaces (SFP optical interfaces), through which it can be
connected to at most four OPCOM31xx series devices.



Provide high-density interfaces, and thus is of high access ability.



The STM-1 optical interface can be set to independent mode or 1+1 line multiplexing
section protection mode. When set to the later, interfaces 1 and 2 protect each other, and
interfaces 3 and 4 protect each other.



Support low order path 1+1 protection.



When two OPCOM3500E-4STM1-S are installed, they support inter-card 1+1
protection.



Support the inband NMS and outband NMS. The inband NMS transmits NMS
information through VC12. The outband NMS transmit NMS information by occupying
DCC bytes.



The bandwidth of NMS channel can be set to192 Kbit/s, 576 Kbit/s, and 768 Kbit/s.



Support remote LPR detection connected to the similar STM-1-supportive devices of
Raisecom.



Support complete alarm and performance monitoring.



Support Digital Diagnostics Monitoring (DDM) of the SFP module.



Support ALS.



Support online software upgrade over local and remote devices.



Support hot swapping.

7.2.2 Slots

The OPCOM3500E-4STM1-S can be plugged into slots 1–5 and 8–12 on the iTN2100.

«
...
68
69
70
71
72
...
»

Summary of Contents for iTN2100

























































































































































































































































































































Reviews:

No comments