manualshive.com logo in svg

Raisecom iTN2100, Hardware Description, Page: 62 / 312

Share
Download
Raisecom iTN2100 Hardware Description Download Page 62

Raisecom 
iTN2100 (P100R002) Hardware Description 

6 SDH aggregation card 

 

 

Raisecom Technology Co., Ltd. 

33 

 

Table 6-7

 

Alarms of the OPCOM3500E-2STM1/4-M 

Alarm 

Cause 

Level 

RS-LOS 

 

Attenuation of received signals is over great. 

 

The peer sender fails. 

 

The connector of fiber is dirty or improperly connected. 

 

The local receiver fails. 

Critical 

RS-LOF 

 

The TX clock of the peer device fails. 

 

Optical signals do not match. 

 

The local RX reference clock fails. 

Critical 

RS-TIM 

 

The received trace byte of the local device and the sent trace 
byte of the peer device are inconsistent. 

 

Services are improperly configured. 

Critical 

AU-AIS 

 

The AU-AIS alarm of the VC4 channel is triggered by MS-
AIS, R-LOS, or R-LOF alarms. 

 

Services are improperly configured. 

 

The peer device sends AU-AIS alarms. 

 

The TX part of the peer device or the RX part of the local 
device fails. 

Minor 

AU-LOP 

 

The RX part of the peer device fails. 

 

Services are improperly configured on the peer device. 

 

Bit Error Rate (BER) of the local device is over great. 

Critical 

MS-EXC 

 

BER in the multiplexing section is over high. 

 

Optical signals are improperly transmitted. 

 

The performance of the local card is bad. 

Major 

MS-AIS 

Multiplexing section alarm LED 

 

Alarm signals are inserted in the optical signals sent by the 
peer device. 

 

The peer device is a regenerator and receives LOS, LOF, or 
OOF alarms. 

Minor 

HP-LOM 

High-order Path (HP) Loss of Multiframe (LOM) alarm 

 

Services are improperly configured. 

 

Byte H4 is lost or incorrect. 

Critical 

HP-TIM 

HP Trace byte (J1) mismatch alarm 

 

The received HPtrace byte of the local device and the sent 
HP trace byte of the peer device are inconsistent. 

 

Services are improperly configured. 

Critical 

HP-PLM 

HP signal marking byte (C2) mismatch alarm 

 

The received signal marking byte of the local device and the 
sent signal marking byte of the peer device are inconsistent. 

 

Services are improperly configured. 

Critical 

TU-AIS 

 

Services are improperly configured. 

 

The channel of the peer device fails. 

 

Higher–level alarms, such as R-LOS, trigger the alarm. 

 

The crossconnection card fails, SDH data received from the 
backplane is incorrect. 

Minor 

TU-LOP 

 

The interface between the tributary card and the cross 
connection card fails. 

 

Services are improperly configured. 

Critical 

LP-TIM 

 

The Low-order Path (LP) trace identifiers of the local device 
and the peer device are inconsistent. 

 

Services are improperly configured. 

Critical 

Summary of Contents for iTN2100

























































































































































































































































































































Reviews:

No comments