Raisecom iTN2100 Hardware Description Download Page 53 | Manualshive

Page: 53 / 312

Raisecom iTN2100 Hardware Description Download Page 53

Raisecom
iTN2100 (P100R002) Hardware Description

5 NMS card

Raisecom Technology Co., Ltd.

24

5.1 iTN2100-NMS

5.1.1 Appearance and functions

Appearance

Function

The iTN2100-NMS is a NMS card specially used on the iTN2100.



Provide a console interface.



Provide the user byte interface.



Provide a NMS interface and an extended NMS interface.



Provide a manual reset button through which you can reset the card.



Provide a buzzer control button.



Support insertion and plugging, configuration, and query of cards, alarms, performance,
maintenance, and management.



Provide Virtual Channel Connection (VCC) channel through E1 signals. Through this
function, you can manage a remote iTN2100 through the transportation network. The
iTN2100 supports four VCC channels at most.



Support four DCC channels by each slot. Each DCC channel supports three modes: D1-
D3, D4-D12, D1-D12.



Support monitoring and control of revolving speed of fans.



Support a way of input alarms and a way of output alarms.



Support monitoring of working status of power supplies.



Support automatical recovery of configuration data.



Support automatical discovery of Network Element (NE) topology.



Support end-to-end management of the iTN2100.



Support online software upgrade for local and remote devices.



Support hot swapping.

5.1.2 Slots

The iTN2100-NMS can be plugged into slot 0 of the iTN2100.

«
...
51
52
53
54
55
...
»

Summary of Contents for iTN2100

























































































































































































































































































































Reviews:

No comments