Raisecom iTN2100 Hardware Description Download Page 42 | Manualshive

Page: 42 / 312

Raisecom iTN2100 Hardware Description Download Page 42

Raisecom
iTN2100 (P100R002) Hardware Description

4 Power supplies

Raisecom Technology Co., Ltd.

13

4.1 SUB-PWRII-DC/DC-300

4.1.1 Appearance and functions

Appearance

Function

The SUB-PWRII-DC and SUB-PWRII-DC-300 are unintelligent DC power supplies.
The SUB-PWRII-DC has two types: -48 V/150 W and 110 V/300 W.



Provide power switch.



5 V power to the backplane. Then, the backplane supplies power to other
cards.



Perform Electromagnetic Compatibility (EMC) filtering over input power.



Support hybrid input of AC and DC power.



Support hybrid input of intelligent and unintelligent power.



Support input reverse polarity protection (recoverable), input undervoltage
protection, output overvoltage protection, output current limit protection.



Support over temperature protection.



Support input surge current suppression.



Support in-position monitoring and fault reporting.



Support 1+1 hot backup.



Support hot swapping.

4.1.2 Slots

The SUB-PWRII-DC/DC-300 can be plugged into slots POWER1 and POWER2 on the
iTN2100.

«
...
40
41
42
43
44
...
»

Summary of Contents for iTN2100

























































































































































































































































































































Reviews:

No comments