Raisecom iTN2100 Hardware Description Download Page 133

Page: 133 / 312

Raisecom
iTN2100 (P100R002) Hardware Description

13 EOP cards

Raisecom Technology Co., Ltd.

104

13.7 OPCOM3500E-EOPS-8E1

13.7.1 Appearance and functions

Appearance

Function

The OPCOM3500E-EOPS-8E1 is an EOP-to-EOS card with unbalanced interfaces used by
the iTN2100.

The OPCOM3500E-EOPS-8E1 has identical features.



Provide one DB37 interface by the front panel, supporting 8 E1 channels which are
independent from each other or reversely multiplex.



Reversely-multiplexed Ethernet services can be assigned based on N × VC12 to be
transmitted to the SDH network.



Support framed and unframed modes by the E1 interface. They can be configured through
the software.



Support local and remote loopbacks on E1 links.



Support making statistics on the number of received packets, transmitted packets, error
packets, and traffic.



Support selecting a clock mode: local clock or line clock.



Support optional E1 link BERT.



Support GFP and LAPS Ethernet encapsulation modes.



Support VCAT and Link Capacity Adjust Scheme (LCAS).



Provide complete alarm and performance monitoring.



Support managing any Raisecom RC95x family remote protocol convertor regardless
whether the device is directly connected or connected through a device from other
vendors.



Support hot swapping.

13.7.2 Slots

The OPCOM3500E-EOPS-8E1 can be plugged into slots 1–5 and 8–12 on the iTN2100.

Summary of Contents for iTN2100

























































































































































































































































































































Search results

Summary of Contents for iTN2100

Reviews:

Raisecom iTN2100, Hardware Description, Page: 133 / 312

Search results

Summary of Contents for iTN2100

Reviews: