Raisecom ISCOM2600G-HI (A) Series Configuration Manual Download Page 549 | Manualshive

Page: 549 / 581

background image

Raisecom
ISCOM2600G-HI (A) Series Configuration Guide

12 System management

Raisecom Proprietary and Confidential

Copyright © Raisecom Technology Co., Ltd.

518

Max number of log server:     10
Current log server number:    1
Target Address      Level             Facility       Sent      Drop
Discriminator
-------------------------------------------------------------------------
--------------
20.0.0.168          warnings(4)       local7         0         0         0

12.6 Alarm management

12.6.1 Introduction

Alarm means when a fault is generated on the ISCOM2600G-HI series switch or some
working condition changes, the system will generate alarm according to different faults.

Alarm information is used to report some urgent and important events and notify them to the
network administrator promptly, which provides strong support for monitoring device
operation and diagnosing faults.

Alarm information is stored in the alarm buffer. Meanwhile, the alarm is generated to log
information. If a Network Management System (NMS), the alarm will be sent to network
management system through SNMP. The information sent to the NMS is called Trap
information.

Alarm classification

Alarms can be divided into three types according to properties:



Fault alarm: refer to alarms for some hardware fault or some abnormal important
functions, such as port Down alarm;



Recovery alarm: refer to alarms that are generated when device failure or abnormal
function returns to normal, such as port Up alarm;



Event alarm: refer to prompted alarms or alarms that are generated because of failure in
relating the fault to the recovery, such as alarms generated by failing to Ping.

Alarms can be divided into five types according to functions:



Communication alarm: refer to alarms related to the processing of information
transmission, including alarms that are generated by communication fault between
Network Elements (NE), NEs and NMS, or NMS and NMS.



Service quality alarm: refer to alarms caused by service quality degradation, including
congestion, performance decline, high resource utilization rate, and the bandwidth
reducing.



Processing errored alarm: refer to alarms caused by software or processing errors,
including software errors, memory overflow, version mismatching, and the abnormal
program aborts.



Environmental alarm: refer to alarms caused by equipment location-related problems,
including the environment temperature, humidity, ventilation and other abnormal
working conditions.

«
...
547
548
549
550
551
...
»

Summary of Contents for ISCOM2600G-HI (A) Series






































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ISCOM2600G-HI (A) Series

Brand: Dataprobe Pages: 31

Brand: IBM Pages: 13

Flex System EN2092

Brand: IBM Pages: 2

4-Port PoweredUSB 2.0 Hub 011006

Brand: CyberData Pages: 4

Brand: Cabletron Systems Pages: 120

Brand: Cabletron Systems Pages: 110

Brand: VADA Pages: 4

Brand: Maiwe Pages: 5

Brand: Zonet Pages: 7

Brand: Tripp Lite Pages: 3

Brand: Optone Pages: 10

Brand: ZIMCO Pages: 7

Brand: Goobay Pages: 2

ePowerSwitch 8XM Master

Brand: ADDER Pages: 2

Brand: Foxun Pages: 7

Brand: EMP-Centauri Pages: 4

Brand: Microsens Pages: 42

Brand: Brocade Communications Systems Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands