manualshive.com logo in svg

Radwin 5000, Configuration Manual

Share
Download
Radwin 5000 Configuration Manual Download Page 231

RADWIN

 

5000

 

Configuration

 

Guide

Release

 

4.9.17

13

‐

4

HBS

 

Management

Using

 

the

 

Web

 

Interface

13.7

 

HBS

 

Management

13.7.1

 

The

 

Main

 

Window

Figure

 

13

‐

2:

 

Web

 

interface

 ‐ 

Main

 

window,

 

HBS

The

 

Sector

 

ID

 

(EBGX20560334)

 

appears

 

all

 

or

 

in

 

part

 

as

 

the

 

heading.

 

The

 

HBS

 

Info

 

panel

 

is

 

self

 

explanatory.

 

The

 

green

 

Active

 

indicator

 

will

 

vary

 

according

 

to

 

the

 

status

 

of

 

the

 

HSU

 

shown

 

by

 

the

 

RADWIN

 

Manager.

Figure

 

13

‐

3:

 

Sector

 

Status

 

panel

(it

 

will

 

typically

 

be

 

Active,

 

Inactive,

 

Probing

 

etc.)

The

 

bottom

 

panel

 

shows

 

all

 

member

 

HSUs.

 

The

 

green

 

LED

 

icons

 

will

 

change

 

color

 

to

 

reflect

 

the

 

status

 

of

 

HSUs.

 

For

 

example,

 

deregistering

 

an

 

HSU

 

will

 

change

 

it

 

to

 

black

 

as

 

in

 

the

 

RADWIN

 

Manager.

Summary of Contents for 5000





























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands