RadioLink RC4GS V3 Instruction Manual Download Page 37 | Manualshive

Page: 37 / 40

background image

RadioLink Electronic Limited

www.radiolink.com

36

III. Tutorials

3.1 Firmware Update of RC4GS V3

Video tutorial

：

https://www.youtube.com/watch?v=XLyTnSlou-4

Firmware update steps:
1. Check the firmware version in the basic menu--LANGUAGE before firmware update.

2. Download the newest firmware in RadioLink official website. (www.radiolink.com/rc4gsv3_firmware)
3. Power off RC4GS V3. And then connect it to the computer with a USB cable.

4. Power on RC4GS V3.
Note: The screen won’t light up at this time.
5. Don’t need to format the Drive of the transmitter. Just copy the newest firmware and paste it into the Drive.
Note: The original firmware will be kept if you don’t copy the newest firmware after connection
6. Unplug the USB cable. Firmware update is done.
After firmware update, check the firmware version in the basic menu--LANGUAGE to confirm firmware
update.

«
...
35
36
37
38
39
...
»

Summary of Contents for RC4GS V3









































Reviews:

No comments

Related manuals for RC4GS V3

TLE Scalable 150

Brand: GE Pages: 6

Brand: GE Pages: 3

Brand: GE Pages: 80

PACSystems* RX3i

Brand: GE Pages: 39

PACSystems* RX3i

Brand: GE Pages: 35

PACSystems* RX3i

Brand: GE Pages: 3

PACSystems* RX3i

Brand: GE Pages: 169

PACSystems RX7i

Brand: GE Pages: 317

Brand: Data I/O Pages: 88

Brand: Data Aire Pages: 13

Brand: Daikin Pages: 46

Brand: Daikin Pages: 26

ArtNet-DMX Mux16

Brand: DMX4ALL Pages: 21

Brand: Paser Pages: 2

Brand: Computer Automation Technology Pages: 55

FAREX SR MINI SYSTEM

Brand: RKC INSTRUMENT Pages: 82

FX-COMM4NDER MFX3203

Brand: Magicfx Pages: 16

Brand: Fancom Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands