background image

23

EN

  CAUTION!

Risk of crushing injuries to the hand when work-
ing with the roller shutter box open. 

 

‹

Never reach into the area of the winding shaft 
when the motor is running.

  ATTENTION!

The roller shutter may be damaged in case of 
incorrect manual adjustment of the end points.

 

‹

Never dismantle the mechanical stoppers or the 
end rail from the final roller shutter slat.

 

‹

 Do not allow the shutter to knock against the 
mechanical stoppers and maintain a safety gap 
of 2 - 3 cm.

9.  Self-learning mode with smooth stop

 

   WARNING!

WARNING!

Risk of fatal injury (electric shock) due to tear-
ing off the motor cable (15).

 

‹

Ensure that the motor cable 

(15)  

is not taken up by the winding  
shaft 

(5)

 or torn off during the setting process.

Important conditions for adjusting  
the end points and for safe operation

 

‹

 End points must be set in order to switch off the 
motor when they are reached for both directions 
of travel, up ( )/down ( ).

 

‹

 The tubular motor must be fully installed.

 

‹

 There must be a suitably fixed limit (e.g. a win-
dow sill) in the area of the lower end point if the 
end point is to be set automatically.

You can also adjust the end points manually  
if required:

 

‹

Manual adjustment of the upper and lower end 
point, e.g. during the initial installation.

 

‹

Manual adjustment of an end point in combina-
tion with the self-learning mode.

The RolloTube M-line is delivered from the factory in 
self-learning mode with a smooth stop and can be 
put into operation immediately after the electrical 
connection.

10.  Manual adjustment of end points

1. 

Switch on the mains power supply.
The RolloTube M-line is ready for operation imme-
diately.

2. 

 

Move the roller shutter up and down.
The end positions for the smooth stop 
are automatically learned during the 
first run cycles.

3. 

Subsequently check the direction of travel of the 
roller shutter. 
Switch the lines for the rotation direction if the direc-
tion of travel is wrong, see connection diagram 

[ 26 ]

 

on page 21.

  ATTENTION!

The roller shutter may run into the roller shutter 
box in self-learning mode and be damaged with-
out stoppers or an end rail.

 

‹

Always fit two stoppers or an end rail to the roller 
shutter 

(17)

see page 18. 

 

‹

Never dismantle the mechanical stoppers or the 
end rail from the final roller shutter slat.

Initial installation

For initial installation, the roller shutter engineer 
can carry out the end point setting with the help 
of the 

set button (11) 

on the motor or with a com-

mercially available 

universal setting cable (21)

 or 

with a

 cord-switch setting unit

.

In order to do so, follow the more detailed informa-
tion provided in the operating manual of the respec-
tive accessories.

Subsequent modification of the end points with 
external controllers

If you want to subsequently modify the end points of 
your tubular motor, you can adjust these with your 
roller shutter controller (e.g. Troll Comfort).

Summary of Contents for RolloTube M-line

































Reviews: