RADEMACHER 1615 45 11 Translation Of The Original Operating And Assembly Manual Download Page 77

Page: 77 / 88

20. Removing the belt in the event of unit failure

In the event that the RolloTron Comfort DuoFern unit fails
and the motor no longer runs, you can use the disengaging
bracket provided in order to fully remove the belt from the
belt winder unit, without the need for cutting it.

Remove the mains plug from the socket.

Dismantle the RolloTron Comfort DuoFern as previously

demonstrated on page 75.

Release the drive with the help of the supplied disengaging
bracket. A small amount of resistance must be overcome
when pressing.

Maintain pressure on the disengaging bracket and pull the
belt out of the RolloTron as far as possible.

RolloTron

Comfort

DuoFern

RolloTron

Comfort

DuoFern

Plus

Drive release

Storage bay

Drive release

WARNING!

There is a risk of injury as the roller shutters may slam
shut or fall in an uncontrolled manner.

◆

Secure the roller shutters from falling.

◆

Hold on to the belt tightly to stop the roller shutters
from slamming shut or falling in an uncontrolled
manner.

◆

Get a second person to help you unlatch the unit.

Release the belt from the fastening hook and pull it out
completely from the RolloTron.

Replace the disengaging bracket in its holder.

Summary of Contents for 1615 45 11

























































































Search results

Summary of Contents for 1615 45 11

Reviews:

Related manuals for 1615 45 11

Brands by name

Popular brands

RADEMACHER 1615 45 11, Translation Of The Original Operating And Assembly Manual

Search results

Summary of Contents for 1615 45 11

Reviews:

Related manuals for 1615 45 11

Brands by name

Popular brands