background image

 

15 

   

PREPARING FOR OPERATIONS 

 

WHEN  MIXING  GASOLINE  WITH  TWO  CYCLE  ENGINE  OIL,  USE 
ONLY GASOLINE WHICH CONTAINS NO ETHANOL OR METHANOL 
(TYPES  OF  ALCOHOL).  THIS  WILL  HELP  TO  A  VOID  POSSIBLE 
DAMAGE TO ENGINE FUEL LINES AND OTHER ENGINE PARTS. 
DO NOT MIX GASOLINE AND OIL DIRECTLY IN THE ENGINE FUEL 
TANK. 
 
IMPORTANT:  Failure  to  follow  proper  fuel  mix  instructions  may  cause 
damage to the engine. 
 
1.

 

When  preparing  fuel  mixture,  mix  only  the  amount  needed  for  the  job 
you  are  to  do.  Do  not  use  fuel  that  has  been  stored  longer  than  two 
months. Fuel mixture stored longer than this will cause hard starting and 
poor  performance.  If  fuel  mix  has  been  stored  longer  than  this  time.  It 
should be removed and filled with fresh mixture. 

 

                                   

 

WARNING 

,!

    DANGER 

 
2.

 

Never fill the fuel tank to the very top. 

3.

 

Never add fuel to the tank in a closed non-ventilated area. 

4.

 

Do not add fuel to this unit close to an open fire or sparks. 

5.

 

Be sure to wipe off spilled fuel before attempting to start engine 

6.

 

Do not attempt to refuel a hot engine 

 
CHECK POINTS BEFORE OPERATION 
1.

 

Check for loose bolts. Nuts and fittings. 

2.

 

Check  the  air  cleaner  for  dirt.  Clean  the  air  filter  of  all  dirt.  Etc.  before 
operation. 

3.

 

Check to be sure that protector is securely in place. 

4.

 

Check to be sure that is not leak. 

5.

 

Check to be sure the blade is not running in idling speed. 

 

WARNING 

,!

    DANGER 

 
The  engine  exhaust  from  this  product  contains  chemicals  known  to 
cause cancer, birth defects, or other reproductive harm. 
 

 

 
 

Summary of Contents for RAC25PB























Reviews: