-4-
-5-
OPERATING INSTRUCTIONS
• This product may arrive partially charged from the manufacturer. It is recommended
to fully charge the unit immediately after purchase and before using for the first time.
• If the red charge level indicator comes on after pressing the battery check button (5),
fully
recharge
the
unit.
• The charging LED indicator will be illuminated red while charging. When charging is
complete the LED will change to green and stay green until the charging plug is
removed or the charger is switched off at the mains.
• Do not charge the battery for more than 24 hours continuously.
• Make sure that any electrical outlet, located in a potentially wet or moist area, to be
used to charge the unit, is protected by a RCB unit.
• Do not charge the unit on a boat, boat ramp or docks since the electrical cords and
outlets used for charging could cause severe electrical shock if they get wet.
• It is recommended the unit is in an upright position while charging.
NOTE:
MAKE SURE BOTH CABLE CLAMPS (POSITIVE & NEGATIVE) ARE PLACED
IN THEIR STORAGE HOLSTER WHEN NOT IN USE.
HOW TO CHARGE
The internal battery should only be charged using the accessories supplied. Two means
of charging the internal battery are available:
A. Via the AC charger supplied (1):
1. Insert the AC charger plug (1) into the charging jack point (4)
2. Insert the AC charger into a mains outlet.
3. Fully charge the unit to the following
• Initial first time charge: 24 hrs continuously
• Recharge or between each use: up to 36 hrs continuously.
4. When charging is complete unplug the AC charger (1) from the mains outlet then
remove the plug from the units charging point (4).
Note:
Do not allow battery to be completely depleted.
B. Via 12v supply using the cigarette lighter adaptor, item 2
NOTE:
Ensure that the vehicle supply has a 12 volt negative earth system.
The engine of the vehicle supply needs to be running to ensure charging process.
The recommended method of charging is via the AC charger.
1. Insert the DC charger lead (2) into the units charging jack point (4).
2. Insert the DC charger lead (2) into the vehicle accessory socket.
3. Charge the unit for up to 10 hours continously while the vehicles engine is running.
4. When charging is complete unplug lead from the cars accessory socket first and
then from the charging jack point (4) on the unit.
DC12V Output
This unit provides two 12V DC outputs which can be used to drive other 12V DC
accessories with a total rating 10 Amp’s or less.
• Insert cigarette plug of the product to be powered into the 12V DC cigarette socket
(item 3).
NOTE:
Do not exceed the total maximum load of 10 Amp.
Charging & Recharging:
Warning:
Do not overcharge this unit. Prior to charging the unit read and understand all
instructions listed below. Overcharging may result in damage to the unit.
SAFETY INSTRUCTIONS
Follow basic safety principles to reduce risk of personal injury, electric shock and fire.
Please read the following instructions prior to operating this product and keep for future use.
WARNING
• Do not let children handle the tool, all
onlookers should be away from your
work area. Work in an uncluttered area.
• This product may be used outdoors. Do
not leave it exposed to the elements.
Do not use the tool in damp or wet areas.
• Protect the tool from direct sunlight. Do
not use the tool near flammable gases
or liquids. Check cables before
operation. Battery may explode due to
over-heating.
• Do not carry the tool by the cable or pull
the cable to remove the plug from the
mains socket. Protect the cable from
sharp objects, heat and oil. Have it
replaced if damaged.
• Always ensure the tool is not damaged.
Do not operate if either of the cables are
damaged. Consult a qualified person for
repair.
• Do not attempt to repair or open this tool
(which contains no user serviceable
parts).
• The internal battery is a sealed lead acid
battery. It is classified as non-spillable
and has unique sealing techniques to
guarantee that no electrolyte leakage will
occur.
• Do not allow the battery, at any time, to
become totally discharged. The product
should be kept fully charged when not in
use. If kept in storage it must be
recharged every 2 months.
• The product is designed for use with
12V systems only. Do not use engine
starter for any purpose other than that is
designed. For best performance do not
use more than one output at a time.
• When using the 12V DC output socket,
ensure that the plug of the item you are
to power has the positive lead to the
centre pin of the plug.
• The product is not designed to be used
as a replacement to a vehicle battery.
• Never allow the NEGATIVE and
POSITIVE leads on this unit to touch
each other OR the same metal object.
• Ensure the posts and clamps of the
vehicle battery are perfectly clean before
use.
• When connecting the engine starter
leads to a battery, always connect the
RED (positive, +) clamp to the unearthed
battery terminal first, then connect the
BLACK (negative, -) clamp to the chassis
or suitable engine bolt, well away from
the battery and fuel line.
• To prevent battery overheating and
consequent damage, do not exceed our
recommendations for jump starting.
• When engine starting ensure the area is
well ventilated.
• Do not attempt to boost charge the
engine starter's sealed battery.
