S
TART
Quick-Start Guide
Part No. 81-9059-0651-0 Rev. A
Carefully unpack your Integrity CS Unit from shipping container
and verify package contents against contents listed below.
Visually inspect the unit for any signs of damage in shipment or
transit.
If any components are missing or damaged, contact QuStream
Customer Service.
Q
UICK
S
TART
G
UIDE
2
Step
U
NPACK THE
P
ROCESSOR
R
ACK
U
NIT
1
2
P
ACKAGE
C
ONTENTS
:
1
Step
I
NTEGRITY
CS S
ERIES
PROC501, 502, 503 P
ROCESSOR
If any components are missing or damaged, contact QuStream
Customer Service by phone or e-mail.
Customer Service:
1+ (256) 726-9222
Toll Free:
(800) 323-7372 (US and Canada)
Fax:
1+ (256) 726-9268
Email:
V
ERIFY
A
LL
I
TEMS
S
HOWN
A
BOVE
A
RE
I
NCLUDED
W
ITH
U
NIT
U
NPACK
S
HIPPING
C
ONTAINER
Considerations for mounting location include proximity to signal sources/destinations, availability
of primary power and availability of a source of external sync.
Mount the chassis frame in an equipment rack and secure frame to rack using four rack mount
screws.
Do not apply power until all external connections are made and verified.
R
EAR
P
ANEL
L
AYOUT
Each PROC500 Series processor module is fully independent. If your frame is a PROC502
or PROC503 that contains multiple modules, each module is a stand-alone processor.
Complete video and audio connections to each processor module using the diagram below
as a reference. Highlighted connection points indicate major function connections.
P
OWER
C
ORD
E
THERNET
(RJ45)
J
UMPER
C
ABLE
2
Step
G
ET
A
CQUAINTED
The Integrity CS PROC500 Series are self-contained ingest
synchronizers with recursive noise reduction for analog and
SD-SDI signals. Each PROC500 converts composite analog
to SD-SDI, syncs SDI to an external reference; plus it contains
a contains a full RGB color corrector video legalizer, and an
audio embedder/de-embedder. It accepts an input of
composite (NTSC/PAL) analog video or SD-SDI digital video
and produces 2 SD-SDI outputs.
Inputs are provided for up to four analog and three AES audio
sources* for embedding. De-embedded audio is available as
up to 2 AES pairs,* selectable from any de-embedded channel.
PROC501 contains one processor module, PROC502 contains
two modules and PROC503 contains three processor
modules. Each module is identical in all three variations.
G
ET
A
CQUAINTED
(C
ONT
.)
In most installations the Integrity CS processor is controlled by a
LOCAL
control panel installed
to front of chassis frame, as shown above. However, if you have multiple CS units it is possible
to control all of them from one or more controls panels located remote from the chassis frame. If
remote panel option is used, the front control panel is replaced with a front panel equipped with
status lights, but no operating controls. Wiring rear panel connectors for remote operation is
discussed in the last step of this section.
If you are using the
LOCAL
control panel installed on the front of the Integrity CS processor
frame, you MUST install the Ethernet jumper cable to the rear panel connectors for proper
operation. This jumper cable is removed for shipping, but is included in the package with the
processor.
Refer to the following figure, and perform the steps to install this cable prior to use of the
processor.
NOTE
Your Integrity CS Processor WILL NOT function unless this connection is completed.
Your Integrity CS PROC500 Series Processor is composed of a 1RU rack frame with a power
supply and up to three processor modules, installed in card slots on the rear of the chassis. An
illustration of the PROC503 rear panel layout is shown below. PROC502 contains two processor
modules and PROC501 contains one module.
A typical Integrity CS control panel layout is shown in the illustration below.
F
RONT
P
ANEL
L
AYOUT
Input
Ref
Bypass
Test
Freeze
Preset
Setup
Hue
Sel
A1
Menu
Video
Back
Audio
Take/Enter
Gain
A2
Black
A3
Chroma
A4
3
Step
I
NSTALL
R
EAR
P
ANEL
E
THERNET
J
UMPER
4
Step
M
OUNT
PROC500 S
ERIES
C
HASSIS
F
RAME
5
Step
PROCESSOR
M
ODULE
C
ONNECTIONS
V
IDEO
/A
UDIO
C
ONNECTIONS
Locate supplied Ethernet jumper cable shipped with your Integrity processor.
If you are using the LOCAL control panel on the front of the frame to control this unit, install
Ethernet cable jumper between the two Ethernet (RJ45) port connectors on rear panel of
processor.
If you are using a REMOTE control panel over the facility LAN, use an Ethernet switch or hub
to provide an active network connection to BOTH rear panel Ethernet ports.
A
NALOG
A
UDIO
C
ONNECTORS
The illustration and chart identify pin-out for a
typical 6-pin analog audio connector.
Pin Function
+
G
-
Positive Audio Signal
Shield
Negative Audio Signal
SUPPLIED MATING
AUDIO CONNECTOR
+ G - + G -
WIRE RELEASE
WIRE SLOT
MATING AUDIO
CONNECTORS
(A
TTACHED TO REAR
PANEL AUDIO
CONNECTORS
)
*AES INPUTS 1 and 2, and AES OUTPUTS 1 and 2 share same rear panel BNC connectors.
On-board jumpers determine whether each connector is configured as an input or output
connection. It is NOT possible to configure 2 AES INPUTS and 2 AES OUTPUTS
simultaneously
ANALOG AUDIO 1,2,3,4
AES A
AES B
VID A
SDI IN
OUT 1
VID B
OUT 2
ANALOG AUDIO 1,2,3,4
AES A
AES B
VID A
SDI IN
OUT 1
VID B
OUT 2
ANALOG AUDIO 1,2,3,4
AES A
AES B
VID A
SDI IN
OUT 1
VID B
OUT 2
SUPPLIED ETHERNET
CABLE JUMPER
ANALOG AUDIO 1,2,3,4
AES A
VID A
SDI IN
OUT 1
VID B
OUT 2
AES B
ANALOG AUDIO 1,2,3,4
AES A
VID A
SDI IN
OUT 1
VID B
OUT 2
AES B
ANALOG AUDIO 1,2,3,4
AES A
VID A
SDI IN
OUT 1
VID B
OUT 2
PROCESSOR MODULE 3
PROCESSOR MODULE 2
PROCESSOR MODULE 1
MAIN POWER
CONNECTOR
POWER
SWITCH
ETHERNET
CONNECTORS
REDUNDANT
POWER
CONNECTOR
EXTERNAL
SYNC
CONNECTOR
AES B
ANALOG AUDIO 1,2,3,4
AES A
AES B
VID A
SDI IN
OUT 1
VID B
OUT 2
ANALOG AUDIO INPUTS
1 & 2 3 & 4
AES 1
INPUT OR
OUTPUT
AES 2
INPUT OR
OUTPUT
AES 3/
DOLBY-E
INPUT
SD-SDI
SIGNAL
INPUT
ANALOG
SIGNAL
INPUT
SD-SDI OUTPUT
SIGNALS
6
Step
I
NITIAL
P
OWER
U
P
Inspect all connections to the processor. Ensure that all cables are installed securely.
Attach power cord to rear panel main power connector and a source of power.
Move power switch to the “ON” position.
Input
Ref
Bypass
Test
Freeze
Preset
Setup
7
Step
B
ASIC
O
PERATION
C
ONTROL
P
ANEL
L
AYOUT AND
O
PERATION
Direct Entry Pushbuttons
Test
– Pressing
Test
switches output signal
from active video source to a user-selectable
test signal. A second pressing cancels test
output and returns to video source. The
Test
LED illuminates when test output is active.
I
NTEGRITY
CS
PROC500 SERIES
T
ECH
M
ANUAL