Package Contents
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-PRV8408K
_R1
For Style PRV8408K
2016 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
A
Fixture Body
x 1
C
D
Crossbar
Assembly
x 1
RevisedDate:2016-06-01
Cage with Shade
x 1
STEP 1
Install Bulbs, Cage with Shade and Fixture Body
-
A. This fixture uses candelabra bulb with standard screw base.
Maximum 60 watts. Insert bulb and screw snugly into place.
B. Remove Lock Screws from top edge of Cage with Shade (D).
Lock
Screw
Socket
Figure 1
C
C. Insert sockets inside of shade diagonal (Refer
to Direction of Installing Sockets). Rotate
Fixture Body (C) and align holes on fixture
hood to mounting holes on top edge of the
cage. Secure them together with removed
Lock Screws. Tighten until snug with
screwdrivers.
Fixture Hood
Shade
Mounting
Hole
C
D
C
D
D
Bulb (not
Supplied)
Socket
Socket
Direction of
Installing Sockets
Please go to
for product cleaning tips. Go to the
selection.
(2) B10 Candelabra Base bulb 60W Maximum.
20-30 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
www.quoizel.com
Care + Maintenance
Light Source:
Estimated Assembly Time:
Preparation:
Fixture can only be mounted in the direction indicated on page 2.
Tools Required:
Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
B
Alternate
Mounting
screw
x 2
STEP 2
-
Install Crossbar Assembly
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
.
Supply Wires with
Ground Wire
Outlet Box Screws
(not included)
Outlet Box
Figure 2
A
Mounting Screw
or Alternate Short
Mounting Screw
C
Mounting
Ball
A
Backplate
Hex Nut and
Lock Washer
Mounting Screw
or Alternate Short
Mounting Screw
STEP 3
-
Test Fitting Backplate to Crossbar Assembly
A. Remove mounting balls from the Crossbar Assembly (A). Fit the
backplate on Fixture Body (C) to the Crossbar Assembly (A) and
secure with mounting balls. Note: The backplate on Fixture Body (C)
should be snug against the wall and the mounting balls. If not, adjust
the length of the mounting screw or alternate short mounting screw
on the Crossbar Assembly (A) by unscrewing the preassembled hex
nut and lock washer and then screwing the mounting screws or
alternate short mounting screws in or out of the crossbar until the
correct length is achieved. Once the backplate on Fixture Body (C)
is secure, remove the mounting ball and Fixture Body (C) and
proceed to Step 4.
Figure 3
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
