Package Contents
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-HC8413IB
_R1
For Style HC8413IB
2016 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
A
Crossbar Assembly
x 1
Please go to
for product cleaning tips. Go to the
selection.
(1) A21 Medium Base bulb 150W Maximum.
20-30 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams below to ensure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
www.quoizel.com
Care + Maintenance
Light Source:
Estimated Assembly Time:
Preparation:
Fixture can only be mounted in the direction indicated on page 2.
Tools Required:
Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
C
Fixture Body
x 1
ReleasedDate:2016-12-08
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
Glass Panel
x 4
B
Alternate
Mounting
screw
x 2
STEP 2
Installing the Crossbar Assembly
-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure the Crossbar Assembly (A)
with Outlet Box Screws (not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
.
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet
Box
A
Figure 2
Mounting Screw
or Alternate Short
Mounting Screw
STEP 3
Test Fit the Backplate to the Crossbar Assembly
-
A. Remove the mounting balls from the Crossbar Assembly (A). Place
the backplate and Fixture Body (D) onto the Crossbar Assembly (A)
and secure with mounting balls. Note: The backplate and Fixture
Body (D) should be snug against the wall and held tight with the
mounting balls. If it is not, adjust the length of the mounting screw
or alternate short mounting screw on the Crossbar Assembly (A) by
unscrewing the preassembled hex nut and lock washer and then
screwing the mounting screws or alternate short mounting screws
in or out of the crossbar until the correct length is achieved. Once
the backplate and Fixture Body (D) is secure, remove the mounting
ball and Fixture Body (D) and proceed to Step 4.
D
Mounting Ball
A
Backplate
Hex Nut and
Lock Washer
Figure 3
Mounting Screw
or Alternate Short
Mounting Screw
D
STEP 1
-
Attach the Glass Panels to the Fixture Body
A. Unscrew lock screws and remove the cage from the Fixture Body (D).
B. Remove Allen screws and tabs from the top edge of the cage. Insert
the Glass Panel (C) into the slot in the bottom edge of the cage.
Attach tabs onto the top edge of the Glass Panel (C) and line up
holes on tabs to mounting holes on the top of the cage. Secure by
threading Allen screws back into the mounting holes on the top edge
Figure 1
C
Fixture
Hood
D
Allen
Screw
Tab
Cage
Lock
Screw
Slot
of the cage. Tighten until snug
with screwdrivers.
C. Attach the fixture hood onto the
top edge of cage and secure with
lock screws previously removed.
Tighten until snug with
screwdrivers.
