manualshive.com logo in svg

Quectel UG Series, Command Manual

Share
Download
Quectel UG Series Command Manual Download Page 52

                                                                                                                                             

UMTS/HSPA  Module  Series 

                                                                                                              WCDMA  UGxx  AT  Commands  Manual

 

 

WCDMA_UGxx_AT_Commands_Manual                      Confidential / Released                          51 / 247 
 
 

 

 

Parameter 

Example

 

AT+QCFG="temp",-1                         

//Query the low temperature warning limit and setting 

+QCFG: "temp",(-1,-35,0) 

 

OK 

AT+QCFG="temp",-1,-35,1         

     

//Set the low temperature warning limit 

OK 

<Enable  temperature  detection,  when  greater  than  the  lowest  temperature  limit,  lower  than  low 

temperature warning limit>

 

+QIND: "temp",-1                               

//Report result when temperature is lower than warning temperature

 

<Enable temperature detection, when temperature is back to normal temperature range> 

+QIND: "temp",0                                 

//Report result when temperature is back to normal temperature

 

 

4.3.11.  AT+QCFG="fota/cid"    DFOTA Context ID Configuration 

When  you  upgrade  firmware  by  DFOTA  on  a  FTP  server  or  HTTP  server,  you  need  to  activate  a  PDP 

context  ID  for  FTP  connection  or  HTTP  connection.  The  default  PDP  context  ID  is  1,  and  it  can  be 
configured by AT+QCFG=“fota/cid”,<contexitd>. 

<temptype>

 

 

Temperature type 

-2                

Indicate the lowest temperature 

-1               

Indicate low temperature warning 

1                 

Indicate high temperature warning 

2                 

Indicate the highest temperature 

<tempvalue>       

Temperature threshold value (degrees Celsius)   

(-40~-35)      The lowest temperature limit (If below this limit, the module will be shut   

 

 

 

 

 

 

 

down). Default value is -38 

(-35~-30) 

Low temperature warning limit. Default value is -32 

(70~80)   

High temperature warning limit. Default value is 75 

(80~90)          The highest temperature limit (If above this limit, the module will be shut 

down). Default value is 85 

<temponoff>       

Enable/disable temperature detection function 

 

 

 

0       

 

Disable 

1       

 

Enable 

AT+QCFG="fota/cid"    DFOTA Context ID Configuration

 

Write Command 

AT+QCFG="fota/cid"[,<contextID>] 

Response 

If configuration parameters are omitted 

Quectel 

Confidential

Summary of Contents for UG Series

























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands