Quectel UG Series Command Manual Download Page 46

Page: 46 / 248

UMTS/HSPA Module Series

WCDMA UGxx AT Commands Manual

WCDMA_UGxx_AT_Commands_Manual Confidential / Released 45 / 247

The configuration will be saved to NV automatically.

4.3.6.

AT+QCFG="urc/delay" Delay URC Indication

AT+QCFG="urc/delay" can delay the output of URC indication until ring line pulse ends.

Parameter

The configuration will be saved to NV automatically.

4.3.7.

AT+QCFG="tone/incoming" Enable/Disable Ring Tone

AT+QCFG=

“tone/incoming” is used to enable or disable ring tone.

AT+QCFG="urc/delay" Delay URC Indication

Write Command

AT+QCFG="urc/delay"[,<enable>]

Response

If configuration parameter is omitted:

+QCFG: "urc/delay",<enable>

If configuration parameter is entered:

ERROR

If error is related to ME functionality:

+CME ERROR: <err>

Reference

<enable>

URC indication will be output when ring line pulse starts

1 URC indication will be output when ring line pulse ends (only the type of ring

line is “pulse”, refer to

AT+QCFG="urc/ri/ring"

AT+QCFG="urc/ri/smsincoming"

and AT+QCFG="urc/ri/other"

)

AT+QCFG="tone/incoming" Enable/Disable Ring Tone

NOTE

Quectel

Confidential

Summary of Contents for UG Series

























































































































































































































































Search results

Summary of Contents for UG Series

Reviews:

Brands by name

Popular brands

Quectel UG Series, Command Manual

Search results

Summary of Contents for UG Series

Reviews:

Brands by name

Popular brands