manualshive.com logo in svg

Quectel UG Series, Command Manual

Share
Download
Quectel UG Series Command Manual Download Page 35

                                                                                                                                             

UMTS/HSPA  Module  Series 

                                                                                                              WCDMA  UGxx  AT  Commands  Manual

 

 

WCDMA_UGxx_AT_Commands_Manual                      Confidential / Released                          34 / 247 
 
 

 

 

Parameter

 

 

 

1.  If a fixed baud rate is set, make sure that both TE (DTE, usually external processor) and TA (DCE, 

Quectel module) are configured to the same rate. 

2.  If 

IPR 

is set to 0, it will change module to auto baudrate. 

3.  The value of 

AT+IPR

 cannot be restored with 

AT&F

 or 

ATZ

. 

4.  A  selected  baud  rate  takes  effect  after  the  write  commands  are  executed  and  acknowledged  by 

"

OK

". 

Example 

AT+IPR=115200   

 

 

 

 

 

 

//Set fixed baud rate to 115200

 

OK 

AT+IPR? 

+IPR: 115200 

 

OK 

 

3.5. AT+QRIR    Restore Ring Line to Inactive 

 

If the behavior of ring line is "always", you should restore ring line to inactive by AT+QRIR. The behavior 

of  ring  line  is  controlled  by  AT+QCFG.  Please  refer  to  AT+QCFG="urc/ri/ring",  AT+QCFG="urc/ri/other" 

and AT+QCFG="urc/ri/smsincoming". 

<rate>

   

Baud rate of per second       

 

 

 

0 

 

 

 

300 

 

 

 

1200 

 

 

 

2400 

 

 

 

4800 

 

 

 

9600 

 

 

 

19200 

 

 

 

38400 

 

 

 

57600 

 

         

115200 

                        230400 

 

         

460800 

 

 

 

921600 

 

 

 

3000000 

 

 

 

6000000 

NOTES 

Quectel 

Confidential

Summary of Contents for UG Series

























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands