Quectel UG Series Command Manual Download Page 21

Page: 21 / 248

UMTS/HSPA Module Series

WCDMA UGxx AT Commands Manual

WCDMA_UGxx_AT_Commands_Manual Confidential / Released 20 / 247

Z: 0

S0: 0

S5: 8

S6: 2

S7: 0

S8: 2

S10: 15

2.13. AT&W Store Current Parameters to User Defined Profile

AT&W stores the current AT command settings to a user defined profile in non-volatile memory.

Parameter

<n>

Profile 0 to store current parameters

2.14. ATZ Set all Current Parameters to User Defined Profile

ATZ restores the current AT command settings to a user defined profile in non-volatile memory, if one was

storable with AT&W before. Any additional AT command on the same command line may be ignored. ATZ

AT&W Store Current Parameters to User Defined Profile

Execution Command

AT&W[<n>]

Response

TA stores the current parameter settings in the user defined

profile. See Table 8: AT Command Settings Storable with

AT&W.

Maximum Response Time

300ms

Reference

V.25ter

Quectel

Confidential

Summary of Contents for UG Series

























































































































































































































































Search results

Summary of Contents for UG Series

Reviews:

Brands by name

Popular brands

Quectel UG Series, Command Manual

Search results

Summary of Contents for UG Series

Reviews:

Brands by name

Popular brands