Quectel UG Series Command Manual Download Page 165

Page: 165 / 248

UMTS/HSPA Module Series

WCDMA UGxx AT Commands Manual

WCDMA_UGxx_AT_Commands_Manual Confidential / Released 164 / 247

Example

AT+CGEREP=?

+CGEREP: (0-2),(0,1)

AT+CGEREP?

+CGEREP: 0,0

10.13. AT+CGSMS Select Service for MO SMS Messages

AT+CGSMS specifies the service or service preference that the MT will use to send MO (mobile

originated) SMS messages.

Parameter

AT+CGSMS Select Service for MO SMS Messages

Test Command

AT+CGSMS=?

Response

+CGSMS:

(list of currently available

<service>

Read Command

AT+CGSMS?

Response

+CGSMS:

<service>

Write Command

AT+CGSMS=[<service>]

Response

If error is related to ME functionality:

+CME ERROR: <err>

Maximum Response Time

300ms

Reference

3GPP TS 27.007

<service>

A numeric parameter which indicates the service or service preference to be used

Packet domain

Circuit switch

Packet domain preferred (use circuit switched if packet domain service not

available)

Quectel

Confidential

Summary of Contents for UG Series

























































































































































































































































Search results

Summary of Contents for UG Series

Reviews:

Brands by name

Popular brands

Quectel UG Series, Command Manual

Search results

Summary of Contents for UG Series

Reviews:

Brands by name

Popular brands