Quectel UG Series Command Manual Download Page 13 | Manualshive

Page: 13 / 248

background image

UMTS/HSPA Module Series

WCDMA UGxx AT Commands Manual

WCDMA_UGxx_AT_Commands_Manual Confidential / Released 12 / 247

1.5. Unsolicited Result Code

As a report message, URC (Unsolicited Result Code) is not issued as part of the response related to an

executed AT command. URC is issued by the module without being requested by the TE and it is issued

automatically when a certain event occurs. Typical events leading to URCs are incoming calls ("RING"),

received short messages, etc. The AT command AT+QCFG="urc/port" could list all available port(s) and

the current port. This command also can disable URC indication of a specified port.

1.6. Turn off Procedure

It is recommended to execute AT+QPOWD command to turn off the module, as it is the safest and best

way. This procedure is realized by letting the module log off from the network and allowing the software to

enter into a secure and safe data state before disconnecting the power supply.

After sending AT+QPOWD, do not enter any other AT commands. The module outputs message
“POWERED DOWN” and sets the STATE pin as low to enter into the shutdown state. In order to avoid
data loss, it is suggested to wait for 1s to switch off the VBAT after the STATE pin is set as low and the
URC “POWERED DOWN” is outputted. If “POWERED DOWN” has not been received after 65s, the
VBAT shall be switched off compulsorily.

Quectel

Confidential

«
...
11
12
13
14
15
...
»

Summary of Contents for UG Series

























































































































































































































































Reviews:

No comments

Related manuals for UG Series

FEPL-02 Ethernet POWERLINK

Brand: ABB Pages: 2

Brand: ABB Pages: 2

Smart-MPPT Li Series

Brand: Y-Solar Pages: 6

Brand: S-COM Pages: 400

Brand: Data I/O Pages: 88

Brand: Data Aire Pages: 13

Brand: Ultraflex Pages: 7

Brand: Panasonic Pages: 8

MicroTech II UV05

Brand: AAF Pages: 50

Brand: One for All Pages: 15

Brand: Data Aire Pages: 137

Brand: Samson Pages: 44

Brand: HEIDENHAIN Pages: 32

Brand: Watts Pages: 12

XDOM TAKE 6 IR/RF - PRODUCTSHEET

Brand: Ebode Pages: 88

DX99N9X1S2N0M2X0D2

Brand: Banner Pages: 13

Brand: Redback Pages: 3

Brand: TREND Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands