Quectel SC20-EL Manual Download Page 46

Page: 46 / 49

Smart LTE Module Series

Smart EVB User Guide

Smart_ EVB_User_Guide

42 / 45

Figure 39: QCOM Configuration When Communicating via UART Interface

4.4. Firmware Upgrade

Quectel SC20 module upgrade firmware via USB port by default. Please follow the procedures below to

upgrade firmware.

1. Open the firmware upgrade tool

QFIL

on PC and then power on SC20 module according to the

procedures mentioned in

Chapter 4.1

Click the “

SelectPort

” and select the USB port “

Qualcomm HS-USB Diagnostics Modem 9091

(COM24)

”.

Select “

Flat Build

” in “

Select Build Type

” option.

Click “

Browse

” to select the firmware which needs to be upgraded in “

Select Programmer

” option”.

Click “

Load XML

” to select the XML which needs to be upgraded in “

Select Build

” option.

Click “

Download

” to upgrade the firmware.

Summary of Contents for SC20-EL


















































Search results

Summary of Contents for SC20-EL

Reviews:

Related manuals for SC20-EL

Brands by name

Popular brands

Quectel SC20-EL, Manual

Search results

Summary of Contents for SC20-EL

Reviews:

Related manuals for SC20-EL

Brands by name

Popular brands