Quectel RM510Q-GL Hardware Design Download

Page: 41 / 97

5G Module Series

RM510Q-GL Hardware Design

RM510Q-GL_Hardware_Design 40 / 88

⚫

Keep (U)SIM card signals away from RF and VCC traces.

⚫

Make sure the ground between the module and the (U)SIM card connector is short and wide. Keep

the trace width of ground and USIM_VDD no less than 0.5 mm to maintain the same electric

potential.

⚫

To avoid cross-talk between USIM_DATA and USIM_CLK, keep them away from each other and

shield them with surrounded ground.

⚫

To offer better ESD protection, add a TVS diode array of which the parasitic capacitance should be

not high

er than 10 pF. Add 22 Ω resistors in series between the module and the (U)SIM card

connector to suppress EMI such as spurious transmission, and to enhance ESD protection. The 33

pF capacitors are used to filter out RF interference.

⚫

For USIM_DATA, a 10

–20 kΩ pull-up resistor must be added near the (U)SIM card connector.

4.2. USB Interface

The module provides one integrated Universal Serial Bus (USB) interface which complies with the USB

3.1 & 2.0 specifications and supports super speed (10 Gbps) on USB 3.1 and high speed (480 Mbps) and

full speed (12 Mbps) modes on USB 2.0. The USB interface is used for AT command communication,

data transmission, GNSS NMEA sentence output, software debugging, firmware upgrade.

For more details about the USB 3.1 & 2.0 specifications, please visit http://www.usb.org/home.

Table 15: Pin Definition of USB Interface

The USB 2.0 interface is recommended to be reserved for firmware upgrade in designs. The following

figure shows a reference circuit of USB 3.1 & 2.0 interface.

Pin No. Pin Name

I/O

Description

Comment

USB_DP

AIO

USB differential data bus (+)

Require differential
impedance of 90 Ω

USB_DM

AIO

USB differential data bus (-)

USB_SS_TX_M

USB 3.1 super-speed transmit (-)

USB_SS_TX_P

USB 3.1 super-speed transmit (+)

USB_SS_RX_M

USB 3.1 super-speed receive (-)

USB_SS_RX_P

USB 3.1 super-speed receive (+)

Summary of Contents for RM510Q-GL


































































































Search results

Summary of Contents for RM510Q-GL

Reviews:

Related manuals for RM510Q-GL

Brands by name

Popular brands

Quectel RM510Q-GL, Hardware Design

Search results

Summary of Contents for RM510Q-GL

Reviews:

Related manuals for RM510Q-GL

Brands by name

Popular brands