Quectel BG96 At Command Manual Download Page 21

Page: 21 / 23

LTE Module Series

BG96 FILE AT Commands Manual

BG96_FILE_AT_Commands_Manual 20 / 22

Summary of ERROR Codes

The error code <err> indicates an error related to mobile equipment or network. The details about <err>

are described in the following table, and these error codes are only related to file operation of BG96

module.

Table 1: Summary of Error Codes

<err>

Meaning

400

Invalid input value

401

Larger than the size of the file

402

Read zero byte

403

Drive full

405

File not found

406

Invalid file name

407

File already existed

409

Fail to write the file

410

Fail to open the file

411

Fail to read the file

413

Reach the max number of file allowed to be opened

414

The file read-only

416

Invalid file descriptor

417

Fail to list the file

418

Fail to delete the file

419

Fail to get disk info

Summary of Contents for BG96
























Search results

Summary of Contents for BG96

Reviews:

Related manuals for BG96

Brands by name

Popular brands

Quectel BG96, At Command Manual

Search results

Summary of Contents for BG96

Reviews:

Related manuals for BG96

Brands by name

Popular brands