background image

GV200 User Manual

                                                                                                                       

 

Table 8: Electrical conditions of ignition detect 

Logical State 

Electrical State 

Active 5.0V 

to 

32V 

Inactive 

0V to 3V or Open 

 
It is strongly recommended to connect this pin to ignition key to support the power saving 
function when the vehicle is off. 

 

Figure 8: Ignition detection 

Another easy way is to connect PIN14 to a power output in the fuse box of the vehicle which 
is only enabled after the vehicle is ignition on. For example: the power output for radio FM. 

 

3.3.6.

 

Ignition Control 

DOUT1/2/3/4 can be used to control ignition key. They are Open-Drain type with no internal 
pull-up resistor which also be used to control a relay. It means that the user has to connect a 
pull-up resistor or a relay coil between the DOUT1/2/3/4 pin and any positive voltage (32V 
max.) to generate a correct output. The DOUT1/2/3/4 pin can drive a continuous current of 
0.2A. 
 
The electrical conditions of it are: 
 
 

TRACGV200UM001

                                                                                                                                            - 15 -

 

  Queclink 

Confidential

Summary of Contents for GV200




























Reviews: