Qubino
The
INNOVATIVE
and
SMALLEST
Flush Shutter
ORDERING CODE
Z-WAVE FREQUENCY
ZMNHCD1
868,4 MHz
ZMNHCD2
921,4 MHz
ZMNHCD3
908,4 MHz
ZMNHCD4
869,0 MHz
ZMNHCD5
916,0 MHz
ZMNHCD8
865,2 MHz
This Z-Wave module is used to control the motor of blinds,
rollers, shades, venetian blinds, etc … The module can be
controlled either through a Z-Wave network or through the
wall switch.
Precise positioning is supported for motors equipped with
mechanical or electronic end switches. The module is
designed to be mounted inside a “flush mounting box”,
hidden behind a traditional wall switch. Module measures
power consumption of motor and support connection of
digital temperature sensor. It is designed to act as
repeater in order to improve range and stability of Z-Wave
network.
Supported switches
Module supports
mono-stable
switches (push button) and
bi-stable
switches
.
Installation
•
To prevent electrical shock and/or equipment damage,
disconnect electrical power at the main fuse or circuit
breaker before installation or any servicing.
•
Make sure, that no voltage is present in the
installation.
•
Prevent the disconnecting device from being switched
on accidentally.
•
Connect the module according to electrical diagram.
•
Locate the antenna far from metal elements (as far as
possible).
•
Do not shorten the antenna.
Danger of electrocution!
•
Module installation requires a great degree of skill and
may be performed only by a qualified and licensed
electrician.
•
Even when the module is turned off, voltage may be
present on its terminals.
Note!
Do not connect the module to loads exceeding
recommended values. Connect the module only in
accordance to the below diagrams. Improper connections
may be dangerous.
Electrical installation must be protected by directly
associated over current protection fuse 4A, gG or Time
lag T, rated breaking capacity 1500V (ESKA 522.723)
must be used according to wiring diagram to achieve
appropriate overload protection of the module
.
The fuse
must be installed in fuse holder type: Adels contact 503 Si/ 1
DS.
Package contents
•
Flush Shutter
Electrical diagram 230VAC
Notes for the diagram:
WARNING: Service button S
must NOT be used
when
module is connected to 110-230V power supply.
Durability of the device depends on applied load. For
resistive load (light bulbs, etc.) and 4A current consumption
of each individual electrical device, the durability exceeds
70.000 switches of each individual electrical device.
Over-current protection
When the current exceedes 4A, relay is automatically
turned off and “Over-current detected” Notification is sent.
To reactivate the module the power supply has to be turned
off and on again.
Module Inclusion (Adding to Z-Wave network)
•
Connect module to power supply (with
temperature sensor connected - if purchased),
•
auto-inclusion (works for about 5 seconds after
connected to power supply) or
•
press push button I1 three times within 3s (3 times
change switch state within 3 seconds) or
•
press service button
S
(only applicable for 24 V SELV
supply voltage) for more than 2 second.
NOTE1: For auto-inclusion procedure, first set main
controller into inclusion mode and then connect module to
power supply.
NOTE2: When connecting temperature sensor to module
that has already been included, you have to exclude
module first. Switch off power supply, connect the sensor
and re-include the module
.
Module Exclusion/Reset (Removing from
Z-Wave network)
•
Connect module to power supply
•
bring module within maximum 1 meter (3 feet) of the
main controller,
•
enable add/remove mode on main controller,
•
press push button
I1
five times within 3s (5 times
change switch state within 3 seconds) in the first 60
seconds after the module is connected to the power
supply or
•
press service button
S
(only applicable for 24 V SELV
supply voltage) for more than 6 second.
By this function all parameters of the module are set to
default values and own ID is deleted.
If push button I1 is pressed three times within 3s (or service
button S is pressed more than 2 and less than 6 seconds)
module is excluded, but configuration parameters are not
set to default values.
NOTE: If the module is included with parameters 71 with
value different to default and module reset is done, wait at
least 30s before next inclusion
Associations
Association enables Flush Shutter module to transfer
commands inside Z-Wave network directly (without main
controller) to other Z-Wave modules.
Associated Groups
:
Root device:
Group 1: default reporting group (reserved for the main
controller), 1 node allowed.
Group 2: basic on/off (triggered at change of the input I1
state and reflecting its state) up to 16 nodes.
Group 3: basic on/off (triggered at change of the input I2
state and reflecting its state) up to 16 nodes.
Group 4: basic on/off (triggered at sensing moving direction
of roller: up=FF, down=0) up to 16 nodes.
Group 5: basic on/off (triggered at reaching roller position:
bottom=FF, top=0) up to 16 nodes.
Group 6: basic on/off (triggered at reaching roller position:
bottom=FF, not bottom=0) up to 16 nodes.
Group 7: multilevel set (triggered at changes of value of the
Flush Shutter position) up to 16 nodes.
Group 8: multilevel set (triggered at changes of value of
slats tilting position) up to 16 nodes.
Group 9: multilevel sensor report (triggered at change of
temperature sensor) up to 16 nodes.
End point 1:
Group 1: Lifeline group, 0 nodes allowed.
Group 2: basic on/off (triggered at change of the input I1
state and reflecting its state) up to 16 nodes.
Group 3: basic on/off (triggered at change of the input I2
state and reflecting its state) up to 16 nodes.
Group 4: basic on/off (triggered at sensing moving direction
of roller: up=FF, down=0) up to 16 nodes.
Group 5: basic on/off (triggered at reaching roller position:
bottom=FF, top=0) up to 16 nodes.
Group 6: basic on/off (triggered at reaching roller position:
bottom=FF, not bottom=0) up to 16 nodes.
Group 7: multilevel set (triggered at changes of value of the
Flush Shutter position) up to 16 nodes.
End point 2:
Group 1: Lifeline group, 0 nodes allowed.
Group 2: multilevel set (triggered at changes of value of
slats tilting position) up to 16 nodes.
End point 3:
Group 1: Lifeline group, 0 nodes allowed.
Group 2: multilevel sensor report (triggered at change of
temperature sensor) up to 16 nodes.
Automatic calibration
Automatic calibration is a process during which the Flush
Shutter learns the position of the limit switches.
Shutter positioning calibration
(par. 71 set to 0)
There are two procedures of calibration.
Calibration through main controller UI
1) Include the module into the Z-Wave network, according
to module include instructions.
2) Set the parameter 78 (Forced Flush Shutter calibration)
value to 1.
3) Flush Shutter performs the calibration process,
completing full cycle - up, down and up again.
4) Set the parameter 78 (Forced Flush Shutter calibration)
value to 0.
Calibration through the inputs I1 and I2
1) Include the module into the wireless network,
according to module inclusion instructions.
2) Quick press the switch/push-button connected to I1
input and wait until the Shutter reach upper limit switch.
3) Quick press the switch/push-button connected to I2
input and wait until the Shutter reach lower limit switch.
4) Quick press the switch/push-button connected to I1
input and wait until the Shutter reach upper limit switch.
Slates tilting position calibration
(par. 71 set to 1)
When enabling venetian blind mode, position calibration for
slats titling must be done. After doing this, position and
angle of slates can be set. By default full turn time for slates
is set to 1,5s. This value can be changed with parameter
72.
1)
Include and make module calibration according to
section
‘
Shutter positioning calibration’.
2)
Set parameter 71 to 1 ‘Venetian blinds’.
3)
Exclude the module (without reset!)
.
4)
Include the module
.
5)
After module inclusion beside main Shutter widget,
another widget for slates control will appear on UI.
6)
By default full turn movement is set to 1,5s. If this time
is too long (if after slates full cycle Shutter starts
moving up or down), decrease this time defined with
parameter 72.
If this time is to short (if slats will not
turn for full cycle), increase this time defined with
parameter 72.
Manual operation for Shutter
(par. 71 set to 0)
Module allows connecting of push-buttons (mono-stable) or
switches (bi-stable) to I1 and I2 terminals.
Clicking push-button (<2s) connected to I1 (up), initiates up
movement.
Clicking push-button (<2s) connected to I2 (down), initiates
down movement.
If the Shutter is moving, each click, of any push-button, will
stop the movement.
Keeping pressed push-button (>2s) connected to I1 (up),
initiates up movement, until push-button is released.
Keeping pressed push-button (>2s) connected to I2 (down),
initiates down movement, until push-button is released.
Manual operation for venetian blinds
(par. 71 set to 1)
Slates on start position - 0 degree
Clicking push-button (for time < full turn slates time-par.72)
connected to I1 (up), initiates slates turning towards end -
180 degree position, until push-button is released.
Clicking push-button (for time < full turn slates time-par.72)
connected to I2 (down), initiates Shutter down movement.
If the Shutter is moving, each click, of any push-button, will
stop the movement.
Keeping pressed push-button (for time > full turn slates
time-par.72) connected to I1 (up), initiates full slates turn
and up movement, until the push-button is released.
Keeping pressed push-button (for time > full turn slates
time-par.72) connected to I2 (down), initiates Shutter down
movement, until the push-button is released.
Keeping pressed push-button (for time > (full turn slates
time +2s)) connected to I1 (up), initiates up movement, until
push-button is released.
Slates on end position - 180 degree
Clicking push-button (for time < full turn slates time-par.72)
connected to I1 (up), initiates Shutter up movement.
Clicking push-button (for time < full turn slates time-par.72)
connected to I2 (down), initiates slates turning towards
start - 0 degree position, until the push-button is released.
If the Shutter is moving, each click, of any push-button, will
stop the movement.
Keeping pressed push-button (for time > full turn slates
time-par.72) connected to I1 (up), initiates Shutter up
movement, until the push-button is released.
Keeping pressed push-button (for time > full turn slates
time-par.72) connected to I2 (down), initiates full slates turn
and down movement, until the push-button is released.
Keeping pressed push-button (for time > (full turn slates
time +2s)) connected to I2 (down), initiates down
movement, until push-button is released.
Configuration parameters
Parameter no. 10 - Activate/deactivate functions ALL
ON / ALL OFF
Available config. parameters (data type is 2 Byte DEC):
•
default value 255
•
255 - ALL ON active, ALL OFF active.
•
0 - ALL ON is not active ALL OFF is not active
•
1 - ALL ON is not active ALL OFF active
•
2 - ALL ON active ALL OFF is not active
Flush Shutter responds to commands ALL ON / ALL OFF
that may be sent by the main controller or by other
controllers belonging to the system.
Parameter no. 40 - Power reporting in Watts on power
change for Q1 or Q2
Set value means percentage, set value from 0 – 100 = 0% -
100%. Available configuration parameters (data type is 1
N
Neutral lead
L
Live lead
Q1
Output for motor UP (open)
Q2
Output for motor DOWN (close)
I2
Input for switch/push button DOWN (close)
I1
Input for switch/push button UP (open)
TS
Terminal for digital temperature sensor (only for
Flush Shutter module compatible digital
temperature sensor, which must be ordered
separately).
S
Service button (used to add or
remove module from the Z-Wave
network in case of 24 V SELV
power supply).
