manualshive.com logo in svg

Quasonix QSX-RDMS-RM Series, Installation And Operation Manual, Page: 182 / 190

Share
Download
Quasonix QSX-RDMS-RM Series Installation And Operation Manual Download Page 182

 

Rack-Mount RDMS

TM

 Telemetry Receiver 

 

167

 

 Quasonix, Inc. 

 

12  Appendix D 

– Factory Reset Values 

When a reset command is activated, the frequency defaults to the lowest valid frequency for the lowest authorized 
band on the unit. The reset priority is: 

1.

 

QPSK 

2.

 

PCM/FM 

3.

 

SOQPSK 

4.

 

Multi-h CPM 

Reset values for each mode are listed in the following tables. 

 

Table 16: QPSK Factory Reset Values 

Parameter 

Reset State 

Bit Rate 

1 

Modulation Scaling 

N/A 

Clock Polarity 

Normal 

Data Polarity 

Normal 

Derandomizer 

Disabled 

Differential Decoder 

N/A 

IF Filter 

Auto 

Downconvert Antenna 

Disabled 

AGC 

Enabled 

Convolutional Decoder 

Disabled 

Lock Output Polarity 

Active High 

NRZ Encoding 

NRZ-L 

Output Control 

Default 

Output Muting 

Disabled 

Phase Noise Compensation 

Disabled 

Tape Output 

Disabled 

 

 

 

Summary of Contents for QSX-RDMS-RM Series































































































































































































Reviews:

No comments