background image

PLC Driver Manual

2800 & 2900

Compact Operator Interface Terminals

with PLC communication drivers

Quartech Corporation

15943 Angelo Drive

Macomb Township, Michigan 48042-4050

Phone:  (810) 781-0373   FAX: (810) 781-0378

   www.quartechcorp.com

DM2829_PLC Revision 2

Other documents relative to the 2800 & 2900 are:

2800 Hardware Manual, HM2800
2900 Hardware Manual, HM2900
2800/2900 ASCII Driver Manual, DM2829_ASCII
2800 Product Manual, AB Ultra 100, PM2800ABU

The product described in this document can have a variety of uses, the user and those responsible for applying this
equipment must satisfy themselves as to the acceptability of each application and the use of the unit.  Under no
circumstances will QUARTECH CORPORATION be responsible or liable for any damage, including indirect or
consequential losses resulting from the use, misuse, or application of the unit.

The text, illustrations, charts, and examples included in this document are intended solely to help explain applications
of the product.  Due to the many variables associated with specific uses or applications, QUARTECH CORPORATION
cannot assume responsibility or liability for actual use based upon the data provided in this document.

No patent liability is assumed by QUARTECH CORPORATION with respect to the use of circuits, information,
equipment, or software described in this document.

This document is subject to change without notice.

Summary of Contents for 2800


















Reviews: