Quark-Elec QK-W016 Application Note Download Page 15 | Manualshive

Page: 15 / 23

Quark-Elec QK-W016 Application Note Download Page 15

Quark-Elec application note

https://www.quark-elec.com

15 of 23

2015

V1.1

3.1 Temperature setting within the program

Operators can set the upper limit (maximum temperature) and lower limit (minimum

temperature) for the controlled zones via the control panel, so the related relay can be triggered

on or off once the measured temperature has reached the set points. The upper temperature

needs to be at least 1°C higher than the bottom temperature to avoid hysteresis issues.

Figure 11 Temperature control setting

3.2 Temperature data logger

QK-W016 can monitor and record the temperatures at the sensors regularly by setting the
interval times and ticking the boxes at ‘Data log every xx seconds.’ The minimum sample time

intervals are 30 seconds for the PC application and 300 seconds for the mobile Android/iOS

application.

The application or the APP will start to collect the temperature information from QK-W016. This

information is shown on the received message field:

«
...
13
14
15
16
17
...
»

Summary of Contents for QK-W016
























Reviews:

No comments