background image

26

FOR YOUR SAFETY READ BEFORE OPERATING

A. This water heater does not have a pilot light.  It is equipped with an ignition device that automatically 

lights the burner.  Do 

not

 try to light the burner by hand.

B. BEFORE OPERATING smell all around the water heater area for evidence of leaking gas.  Be sure to 

smell next to the floor because some gas is heavier than air and will settle on the floor.

  WHAT TO DO IF YOU SMELL GAS.

•  Do not try to light any appliance.
•  Do not touch any electric switch; do not use any phone in your building.
•  Immediately call your gas supplier from a neighbor's phone.  Follow the gas supplier's 

instructions.

•  If you cannot reach your gas supplier, call the fire department.

C. Use only your hand to turn the gas valve knob.  Never use tools.  If the knob will not turn by hand, 

don't try to repair it.  Call a qualified service technician.  Forced or attempted repair may result in a 

fire or explosion.

D. Do not use this water heater if any part has been under water.  Immediately call a qualified service 

technician to inspect the water heater and to replace any damaged parts.

OPERATING INSTRUCTIONS

1. 

STOP!

 

Read the safety information above or in the Owner's Manual.

2. 

Turn off all electric power to the water heater.

3. 

Do not attempt to light the burner by hand.

4. 

Turn the manual gas valve located on the outside of the unit clockwise to the OFF position.

5. 

Wait five (5) minutes to clear out any gas.  If you then smell gas, STOP!  Follow "B" in the safety 

      information above on this label.  If you don't smell gas, go to next step.

6. 

Turn the manual gas valve located on the outside of the unit counterclockwise to the ON position.

7. 

Turn on all electrical power to the water heater.

8. 

If the water heater will not operate, follow the instructions “to Turn Off Gas to Appliance" and 

     call your service technician or gas supplier.

TO TURN OFF GAS TO APPLIANCE

1. 

Turn off all electric power to the water heater if service is to be performed.

2. 

Turn the manual gas valve located on the outside of the unit clockwise to the OFF position.

WARNING:

  If  you  do  not  follow  these  instructions  exactly,  a  fire  or  explosion  may  result  causing 

property damage, personal injury or loss of life.

Summary of Contents for QI-6S-20





























Reviews: