background image

16

Electromagnetic Compatibility (EMC) Compliances

Product Name Quick Start Guide

Electromagnetic Compatibility (EMC) Compliances

The LTO-3 (Model B) Half-Height Tape Drives are EMC compliant with the following 

regulatory organizations and codes in the countries indicated:

IECEE member 

nations*

IECEE International Electrotechnical 

Commission on Electrical 

Equipment (IECEE) for Mutual 

Recognition of Test Certificates for 

Electrical Equipment “CB Scheme”

CB Scheme per IEC 

60950-1 with details 

and exceptions for 

each member country

Israel

SII

CB Scheme

Taiwan

BSMI

BSMI certification, CNS 

14336

United States

Underwriters Laboratories (UL)

UL/CSA 60950-1

* IECEE member nations include: Argentina, Austria, Australia, Belgium, Brazil, 

Canada, China (PR), Czech Republic, Denmark, Finland, France, Germany, Hungary, 

India, Ireland, Israel, Italy, Japan, (South) Korea, Montenegro, Netherlands, Norway, 

Poland, Russian Federation, Serbia, Singapore, Slovakia, Slovenia, South Africa, Spain, 

Switzerland, Turkey, United Kingdom, and USA.

Country

Regulatory Organization

Compliant to:

Country

Regulatory Organization

Compliant to:

Australia

Australian Communications and 

Media Authority (ACMA)

AS/NZS 3548 (same as 

CISPR 22)

Canada

Industry Canada Digital Apparatus - 

Interference-Causing Equipment 

Standard 

 

(ICES-003)

ICES-003 Digital 

Apparatus

EU member nations

CE

Emissions per CISPR 

22, EN55022 and 

Immunity per CISPR 

24, EN55024

Israel

SII

CISPR 22 and CISPR 24

Japan

Voluntary Control Council for 

Interface (VCCI)

VCCI

New Zealand

Australian Communications and 

Media Authority (ACMA)

AS/NZS 3548 (same as 

CISPR 22)

South Korea

MIC

CISPR 22 and CISPR 24

Summary of Contents for LTO-3



















Reviews: