Quantum DXi4500 User Manual Download Page 42 | Manualshive

Page: 42 / 226

Quantum DXi4500 User Manual Download Page 42

Chapter 2: Basic Operations
Power Supply Indicators

20

Quantum DXi4500 User’s Guide

Figure 9 Ethernet Port LEDs

Link indicator (green)

Activity indicator (amber)

Power Supply Indicators

Each power supply has one LED indicator (see

):

•

Not lit -

the power supply is not plugged in

•

Green

- Indicates the power supply is turned on and operating

correctly.

•

Amber

- Indicates power supply failure.

•

Alternating green and amber

- When hot-adding a power supply,

this indicates that the power supply is mismatched with the other
power supply. Replace the power supply that has the flashing
indicator with a power supply that matches the capacity of the
other installed power supply.

Caution:

All power supplies are hot swappable. When replacing
power supplies, never remove more than one power supply
at a time from the system. Also, before you remove one
power supply, make sure the other power supply is

operating correctly (indicator LED is green).

«
...
40
41
42
43
44
...
»

Summary of Contents for DXi4500



































































































































































































































Reviews:

No comments