Quantum Pro QE1600.1M Instruction Manual Download Page 1

Instruction Manual

• Installation Instructions / Owners Manual •

Due to continuous improvement of the product the Specifications are subject to change without notice.

DB Research L.L.P. 

302 Hanmore Industrial Parkway // Harlingen,

 

TX 78550

ph: 877.787.0101 // fx: 956.421.4513 // www.quantumaudio.net

TM

QE1600.1M • QE2400.1D • QE2000.4

QE2400.4 • QE1200.2

AMPLIFIERS

LIMITED WARRANTY

Quantum Audio warrants any products purchased in the U.S.A. 

from an authorized Quantum Audio dealer. All products are warranted 
to be free from defects in material and workmanship under normal use 
and service for a period of one (1) year. This warranty applies to the 
original purchase only. 

Quantum Audio will either repair or replace (as its option) any unit 

that has been found to be defective and under warranty provided the 
defect occurs within the one (1) year warranty period. 

This limited warranty does not extend to units have been 

subjected to misuse, abuse, neglect, or accident. In Quantum Audio’s 
judgment, products that show evidence of having been altered, 
modi-fied, or serviced without Quantum Audio’s authorization, will be 
ineligible under this warranty. 

To obtain warranty service please contact your retailer or visit our 

website at www.quantumaudio.net for more details. 

Summary of Contents for QE1600.1M









Reviews: