manualshive.com logo in svg

Quantum Data 780C, User Manual

The Quantum Data 780C, a cutting-edge device, revolutionizes your multimedia experiences. Enhance your product understanding and maximize its potential with our comprehensive User Manual. Available for free download at manualshive.com, this manual provides detailed instructions and valuable insights to unlock the full capabilities of the Quantum Data 780C.

Share
Download
background image

780C Multi-Interface Interoperability Tester 

– User Guide 

Page 6 

September 29, 2014 

                                       Revision A1 

 

 

 

 

Note

: 780C Image above shows the front edge with the SD Card slot which is used for storing and loading 

bitmaps, reports and for recovery in the event of a failed upgrade. 

1.4

 

Overview of 780C features 

The 780C Multi-Interface Interoperability Tester provides a rich set of features. The following is a list of 
available options and the key features and benefits of each: 

1.4.1 

Standard features 

The following features are standard with the 780C: 

 

Pattern testing for HDTVs - Enables you to conduct pattern testing for an HDTV through the digital video 
and analog component outputs. Provides dozens of patterns with variation options on most. 

 

Custom bitmaps and pattern scrolling 

– The 780C enables you to import bitmaps for use in pattern testing. 

You can initiate a scroll of these bitmaps with user control over the rate and extent of horizontal movement. 

 

Create custom formats using the standalone Format Editor. 

 

3D bitmap pattern testing 

– The 780C enables you to import 3D bitmaps for use in pattern testing. You can 

create your own bitmaps from any stereoscopic images you have using the Quantum Data Bitmap 
Conversion Tool available from the Quantum Data website: 

http://www.quantumdata.com/apps/3D/BMP_conv.asp

. There are some sample 3D bitmaps on this 

webpage as well. 

 

Video confidence test of an HDMI, HDBaseT or 3G-SDI source device 

– The 780C enables you to view the 

incoming video on the 780C

’s LCD screen. 780C enables the incoming image to be routed out the digital 

video output connector if unused. 780C also enables scrolling to view an entire unscaled 4K image 
received on the HDMI and HDBaseT input ports. 

 

Audio confidence test of an HDMI, HDBaseT or 3G-SDI source device 

– The 780C enables you to listen to 

the incoming LPCM audio through the 780C

’s headphone jack on the front edge or through an embedded 

speaker. There will be no sound when compressed audio is received on the incoming HDMI stream. 

 

Audio Return Channel confidence test of an HDMI 1.4 A/V receiver 

– The 780C can emulate an ARC Tx 

device on its HDMI IN port. Note: The 780C does not support enabling ARC on the AV receiver, therefore 
you will have to enable ARC through some other means. 

Summary of Contents for 780C

















































































































































































































































Reviews:

No comments

Related manuals for 780C

Kanomax S200 Series Quick Manual preview
S200 Series
Brand: Kanomax Pages: 2
Keithley 6512 Instruction Manual preview
6512
Brand: Keithley Pages: 156
DAKOTA ULTRASONICS ZX-1 Instruction Manual preview
ZX-1
Brand: DAKOTA ULTRASONICS Pages: 25
DAKOTA ULTRASONICS MX-3 Operation Manual preview
MX-3
Brand: DAKOTA ULTRASONICS Pages: 36
Saluki S3602 Series User Manual preview
S3602 Series
Brand: Saluki Pages: 312
Evoqua WALLACE & TIERNAN P7 ADVANCED Instruction Manual preview
WALLACE & TIERNAN P7 ADVANCED
Brand: Evoqua Pages: 98
Xtralis IntrusionTrace Quick Start Manual preview
IntrusionTrace
Brand: Xtralis Pages: 13
Tektronix RF Scout Quick Start User Manual preview
RF Scout
Brand: Tektronix Pages: 124
Vectronics PM-30 SWR Owner'S Manual preview
PM-30 SWR
Brand: Vectronics Pages: 2
Resol WMZ Plus Installation & Operation Manual preview
WMZ Plus
Brand: Resol Pages: 24
Chauvin Arnoux C.A 43 User Manual preview
C.A 43
Brand: Chauvin Arnoux Pages: 44
Droplet SP2-D Operator'S Manual preview
SP2-D
Brand: Droplet Pages: 35
Sencore cm2125 Operation And Application Manual preview
cm2125
Brand: Sencore Pages: 75
truflo ULTRAFLO 5000 Operating Manual preview
ULTRAFLO 5000
Brand: truflo Pages: 33
Hanna Instruments HI96725C Instruction Manual preview
HI96725C
Brand: Hanna Instruments Pages: 28
Keithley 6487 Reference Manual preview
6487
Brand: Keithley Pages: 338
Oberheim XK Owner'S Manual preview
XK
Brand: Oberheim Pages: 41
Newton T-DAR T1010MT Installation And Operation Manual preview
T-DAR T1010MT
Brand: Newton Pages: 112

Brands by name

Popular brands

Load more brands